"as " CNS Standards List| Method Test | Wired glass | Method test | Toilet tissue | Iron ores─Methods | Masking Tape | Classification labelling | Assembly tools | |
|
CNS 9145
1988 Edition 660V, Single-Core, Twin-Core, Three-Core Silicon Rubber Insulated Glass Fibber Braided Cable(660V-SSRD, 660V-DSRD, 660V-TSRD) for Marine Use 船用660 V單心、二心、三心矽橡膠絕緣玻璃纖維編織電纜(660 V-SSRD，660 V-DSRD，660 V-TSRD) |
|
|
|
CNS 12370
1988 Edition Method of Test for Fiber Optic Devices ( FOTP-48 On-Line Diameter Measurement) 光纖裝置檢驗法（線上作業之直徑測量法FOTP-48） |
|
|
|
CNS 12209
1988 Edition Sets of High Strength Torque Control Bolt, Hexagon Nut and Plain Washers 控制扭矩之高強度螺栓、六角螺帽及平墊圈組 |
Translated |
|
|
CNS 12373
1988 Edition Method of Test for Fiber Optic Devices ( FOTP-58 Core Diameter Measurement of Graded-Index Optical Fibers ) 光纖裝置檢驗法（斜射率光纖纖核直徑之測量FOTP-58） |
|
|
|
CNS 12372
1988 Edition Method of Test for Fiber Optic Devices ( FOTP-53 Attenuation by Substitution Measurement for Multimode Graded-Index Optical Fibers or Fiber Assemblies Used in Long Length Communications System) 光纖裝置檢驗法（多模斜射率光纖或光纖組件在長距離通訊系統中衰減量之替代量測法FOTP-53） |
|
|
|
CNS 11892
1987 Edition Shears for Flower and Grass Cutting 手剪（修剪花草用） |
|
|
|
CNS 11830
1987 Edition Measuring Methods for Light Emitting Diodes (for Indication) 發光二極體(指示用)測量法 |
|
|
|
CNS 11828
1987 Edition Method of Test for Blast Furnace Slag for Road Construction 道路用高爐爐碴檢驗法 |
Translated |
|
|
CNS 12086
1987 Edition Method of Test for Fiber Optic Devices (FOPT-55 Method for Measuring the Coating Geometry of Optical Fibers) 光纖裝置檢驗法（光纖鍍層幾何形狀之測量法FOTP-55） |
|
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 6071
1987 Edition 600 V Silicon Rubber Insulated Glass Fiber Braided Wires 600 V矽橡膠絕緣玻璃纖維編織電線 |
Translated |
|
|
CNS 12069
1987 Edition Ejector Rod of Die Casting Molds 壓鑄模用頂出桿 |
|
|
|
CNS 712
1987 Edition Brass Screwed Globe Valves (10 kgf/㎠) 黃銅螺紋口球型閥(10 kgf/cm2) |
Translated |
|
|
CNS 11932
1987 Edition Angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 12068
1987 Edition Support of Die Casting Molds 壓鑄模用支座 |
|
|
|
CNS 11934
1987 Edition Stop Bolts of Molds for plastics 塑膠型模用止動螺栓 |
|
|
|
CNS 11895
1987 Edition General Rules for Reliability assured Fixed Mica Capacitors 可靠度保證雲母固定電容器總則 |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for Plastics 塑膠型模用止銷 |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas Flame Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 12085
1987 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求FOTP-54） |
|
|
|
CNS 5535
1987 Edition Small Switch for Single-phase Motors 單相電動機用小型開關 |
Translated |
|
|
CNS 11898
1987 Edition Reliability assured Plastic Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
|
|
CNS 10927
1987 Edition Method of Test for Fiber Optic Devices (FOTP-28 Measuring Failure Point of Optical Waveguide Fiber) 光纖裝置檢驗法（光纖抗強拉度測量法FOTP-28） |
|
|
|
CNS 12070
1987 Edition Ejectorplate Guide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 9114
1987 Edition Symbols of Television and Broadcast Equipment of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電視、播音類符號 |
|
|
|
CNS 11937
1987 Edition Runner Pull Pins of Molds for Plastics 塑膠型模用流道拉銷 |
|
| Find out:3287Items | To Page of: First -Previous-Next -Last | [99] [100] [101] [102] [103] [104] [105] |
