"as " CNS Standards List |
|
CNS 12355
1988 Edition Contrast of MCM Gage to Diameter and Section Area 美規絞線與公制直徑及有效截面積對照表 |
|
|
|
CNS 12372
1988 Edition Method of Test for Fiber Optic Devices ( FOTP-53 Attenuation by Substitution Measurement for Multimode Graded-Index Optical Fibers or Fiber Assemblies Used in Long Length Communications System) 光纖裝置檢驗法（多模斜射率光纖或光纖組件在長距離通訊系統中衰減量之替代量測法FOTP-53） |
|
|
|
CNS 12293
1988 Edition Reliability assured Fixed Carbon Composition Resistors (From 1, Grade X) 可靠度保證混合碳固定電阻器(方式1之等級X) |
Translated |
|
|
CNS 12209
1988 Edition Sets of High Strength Torque Control Bolt, Hexagon Nut and Plain Washers 控制扭矩之高強度螺栓、六角螺帽及平墊圈組 |
Translated |
|
|
CNS 12210
1988 Edition Method of Test for Sets of High Strength Torque Control Bolt, Hexagon Nut and Plain Washers 控制扭矩之高強度螺栓、六角螺帽及平墊圈組檢驗法 |
|
|
|
CNS 12072
1987 Edition Locating Pin of Die Casting Molds 壓鑄模用定位銷 |
|
|
|
CNS 11895
1987 Edition General Rules for Reliability assured Fixed Mica Capacitors 可靠度保證雲母固定電容器總則 |
|
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 11934
1987 Edition Stop Bolts of Molds for plastics 塑膠型模用止動螺栓 |
|
|
|
CNS 12084
1987 Edition Method of Test for Fiber Optic Devices (FOPT-36 Twist Test for Fiber Optic Cable assemblies 光纖裝置檢驗法（光纜組件扭力試驗FOTP-36） |
|
|
|
CNS 12070
1987 Edition Ejectorplate Guide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 12082
1987 Edition Method of Test for Fiber Optic Devices (FOPT-30 Frequency Domain Measurement of Multimode Optical Fiber Information Transmission Capacity) 光纖裝置檢驗法（多模光纖資訊傳輸量之頻域測量FOTP-30） |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 12086
1987 Edition Method of Test for Fiber Optic Devices (FOPT-55 Method for Measuring the Coating Geometry of Optical Fibers) 光纖裝置檢驗法（光纖鍍層幾何形狀之測量法FOTP-55） |
|
|
|
CNS 12071
1987 Edition Angle Pin of Die Casting Molds 壓鑄模用斜角撐銷 |
|
|
|
CNS 12085
1987 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求FOTP-54） |
|
|
|
CNS 6071
1987 Edition 600 V Silicon Rubber Insulated Glass Fiber Braided Wires 600 V矽橡膠絕緣玻璃纖維編織電線 |
Translated |
|
|
CNS 9114
1987 Edition Symbols of Television and Broadcast Equipment of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電視、播音類符號 |
|
|
|
CNS 11937
1987 Edition Runner Pull Pins of Molds for Plastics 塑膠型模用流道拉銷 |
|
|
|
CNS 11938
1987 Edition Sprue Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 12074
1987 Edition Flash Cavity of Hot Forging Closed Die 熱鍛閉合模之餘料穴 |
|
|
|
CNS 5535
1987 Edition Small Switch for Single-phase Motors 單相電動機用小型開關 |
Translated |
|
|
CNS 10927
1987 Edition Method of Test for Fiber Optic Devices (FOTP-28 Measuring Failure Point of Optical Waveguide Fiber) 光纖裝置檢驗法（光纖抗強拉度測量法FOTP-28） |
|
|
|
CNS 10926
1987 Edition Method of Test for Fiber Optic Devices (FOTP-27 Measuring Outside (Uncoated) Diameter of Optical Fibers) 光纖裝置檢驗法（無外被光纖外徑測量法FOTP-27） |
|
|
|
CNS 12080
1987 Edition Glossary of Terms Used in Electronic Measuring Apparatus 電子測定器詞彙 |
|
|
|
CNS 11939
1987 Edition Setting Plugs of Molds for Plastics 塑膠型模用定位塞 |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for Plastics 塑膠型模用止銷 |
|
|
|
CNS 11932
1987 Edition Angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 11898
1987 Edition Reliability assured Plastic Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
| Find out:3287Items | To Page of: First -Previous-Next -Last | [99] [100] [101] [102] [103] [104] [105] |
