"as " CNS Standards List |
|
CNS 12296
1988 Edition Reliability assured Power Type Fixed Wire Wound Resistors (S) (Established Failure Rate) 可靠度保證功率型線繞固定電阻器（特性Ｓ）（故障率設定） |
Translated |
|
|
CNS 12369
1988 Edition Method of Test for Fiber Optic Devices ( FOTP-45 Microscopic Method for Measuring Fiber Geometry) 光纖裝置檢驗法（測量光纖幾何之微觀方法FOTP-45） |
|
|
|
CNS 12292
1988 Edition Reliability assured Fixed Carbon Composition Resistors (Established Failure Rate) 可靠度保證混合碳固定電阻器（故障率設定） |
Translated |
|
|
CNS 12359
1988 Edition Method of Test for Fiber Optic Devices ( FOTP-66 Measuring Relative Abrasion Resistance of Optical Waveguide Coating and Buffers) 光纖裝置檢驗法（鍍層及緩衝層耐磨性之測量FOTP-66） |
|
|
|
CNS 12367
1988 Edition Method of Test for Fiber Optic Devices ( FOTP-43 Output Near-Fiber Raiation Pattern Measuremnnt) 光纖裝置檢驗法（輸出近場放射圖型之測量FOTP-43） |
|
|
|
CNS 8871
1987 Edition Dental Plaster 牙科用普通石膏 |
|
|
|
CNS 712
1987 Edition Brass Screwed Globe Valves (10 kgf/㎠) 黃銅螺紋口球型閥(10 kgf/cm2) |
Translated |
|
|
CNS 5535
1987 Edition Small Switch for Single-phase Motors 單相電動機用小型開關 |
Translated |
|
|
CNS 10926
1987 Edition Method of Test for Fiber Optic Devices (FOTP-27 Measuring Outside (Uncoated) Diameter of Optical Fibers) 光纖裝置檢驗法（無外被光纖外徑測量法FOTP-27） |
|
|
|
CNS 8229
1987 Edition Method of Test For Dry Reed Switches (Operate, Bounce, Release and Transfer (SPDT) Time) 乾式簧開關檢驗法（動作、彈跳、復原與轉接時間） |
|
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (Quality Control and Quality assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 10927
1987 Edition Method of Test for Fiber Optic Devices (FOTP-28 Measuring Failure Point of Optical Waveguide Fiber) 光纖裝置檢驗法（光纖抗強拉度測量法FOTP-28） |
|
|
|
CNS 12072
1987 Edition Locating Pin of Die Casting Molds 壓鑄模用定位銷 |
|
|
|
CNS 11830
1987 Edition Measuring Methods for Light Emitting Diodes (for Indication) 發光二極體(指示用)測量法 |
|
|
|
CNS 11892
1987 Edition Shears for Flower and Grass Cutting 手剪（修剪花草用） |
|
|
|
CNS 11895
1987 Edition General Rules for Reliability assured Fixed Mica Capacitors 可靠度保證雲母固定電容器總則 |
|
|
|
CNS 12082
1987 Edition Method of Test for Fiber Optic Devices (FOPT-30 Frequency Domain Measurement of Multimode Optical Fiber Information Transmission Capacity) 光纖裝置檢驗法（多模光纖資訊傳輸量之頻域測量FOTP-30） |
|
|
|
CNS 11898
1987 Edition Reliability assured Plastic Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 12080
1987 Edition Glossary of Terms Used in Electronic Measuring Apparatus 電子測定器詞彙 |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas Flame Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
|
|
CNS 11932
1987 Edition Angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 11828
1987 Edition Method of Test for Blast Furnace Slag for Road Construction 道路用高爐爐碴檢驗法 |
Translated |
|
|
CNS 12074
1987 Edition Flash Cavity of Hot Forging Closed Die 熱鍛閉合模之餘料穴 |
|
|
|
CNS 12085
1987 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求FOTP-54） |
|
|
|
CNS 12071
1987 Edition Angle Pin of Die Casting Molds 壓鑄模用斜角撐銷 |
|
|
|
CNS 11934
1987 Edition Stop Bolts of Molds for plastics 塑膠型模用止動螺栓 |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for Plastics 塑膠型模用止銷 |
|
| Find out:3287Items | To Page of: First -Previous-Next -Last | [99] [100] [101] [102] [103] [104] [105] |
