"as " CNS Standards List |
|
CNS 12289
1988 Edition Reliability assured Fixed Metal Film Resistors (H,J,K) (Established Failure Rate) 可靠度保證金屬皮膜固定電阻器（特性H，J及K）（故障率設定） |
Translated |
|
|
CNS 12372
1988 Edition Method of Test for Fiber Optic Devices ( FOTP-53 Attenuation by Substitution Measurement for Multimode Graded-Index Optical Fibers or Fiber Assemblies Used in Long Length Communications System) 光纖裝置檢驗法（多模斜射率光纖或光纖組件在長距離通訊系統中衰減量之替代量測法FOTP-53） |
|
|
|
CNS 12373
1988 Edition Method of Test for Fiber Optic Devices ( FOTP-58 Core Diameter Measurement of Graded-Index Optical Fibers ) 光纖裝置檢驗法（斜射率光纖纖核直徑之測量FOTP-58） |
|
|
|
CNS 12210
1988 Edition Method of Test for Sets of High Strength Torque Control Bolt, Hexagon Nut and Plain Washers 控制扭矩之高強度螺栓、六角螺帽及平墊圈組檢驗法 |
|
|
|
CNS 12294
1988 Edition Reliability assured FIxed Carbon Composition Resistors (Form 2,Gradex) 可靠度保證混合碳固定電阻器(方式2之等級X) |
Translated |
|
|
CNS 6071
1987 Edition 600 V Silicon Rubber Insulated Glass Fiber Braided Wires 600 V矽橡膠絕緣玻璃纖維編織電線 |
Translated |
|
|
CNS 5535
1987 Edition Small Switch for Single-phase Motors 單相電動機用小型開關 |
Translated |
|
|
CNS 11898
1987 Edition Reliability assured Plastic Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (Quality Control and Quality assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 9114
1987 Edition Symbols of Television and Broadcast Equipment of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電視、播音類符號 |
|
|
|
CNS 8229
1987 Edition Method of Test For Dry Reed Switches (Operate, Bounce, Release and Transfer (SPDT) Time) 乾式簧開關檢驗法（動作、彈跳、復原與轉接時間） |
|
|
|
CNS 11939
1987 Edition Setting Plugs of Molds for Plastics 塑膠型模用定位塞 |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas Flame Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 12085
1987 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求FOTP-54） |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 12084
1987 Edition Method of Test for Fiber Optic Devices (FOPT-36 Twist Test for Fiber Optic Cable assemblies 光纖裝置檢驗法（光纜組件扭力試驗FOTP-36） |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for Plastics 塑膠型模用止銷 |
|
|
|
CNS 12086
1987 Edition Method of Test for Fiber Optic Devices (FOPT-55 Method for Measuring the Coating Geometry of Optical Fibers) 光纖裝置檢驗法（光纖鍍層幾何形狀之測量法FOTP-55） |
|
|
|
CNS 11938
1987 Edition Sprue Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 11932
1987 Edition Angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 12068
1987 Edition Support of Die Casting Molds 壓鑄模用支座 |
|
|
|
CNS 12069
1987 Edition Ejector Rod of Die Casting Molds 壓鑄模用頂出桿 |
|
|
|
CNS 12070
1987 Edition Ejectorplate Guide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 12071
1987 Edition Angle Pin of Die Casting Molds 壓鑄模用斜角撐銷 |
|
|
|
CNS 12072
1987 Edition Locating Pin of Die Casting Molds 壓鑄模用定位銷 |
|
|
|
CNS 12074
1987 Edition Flash Cavity of Hot Forging Closed Die 熱鍛閉合模之餘料穴 |
|
|
|
CNS 12080
1987 Edition Glossary of Terms Used in Electronic Measuring Apparatus 電子測定器詞彙 |
|
| Find out:3287Items | To Page of: First -Previous-Next -Last | [99] [100] [101] [102] [103] [104] [105] |
