"1 " CNS Standards List |
|
CNS 8241
2019 Edition Method of Starting Test of Carburetors for Automobiles 汽車用化油器起動性能試驗法 |
|
|
|
CNS 15208-2
2019 Edition Linux Standard Base (LSB) core specification 3.1－ Part 2: Specification for IA32 architecture Ｌｉｎｕｘ標準基礎核心(ＬＳＢ Ｃｏｒｅ) 規格第３.１版－第２部: ＩＡ３２架構規格 |
|
|
|
CNS 14922
2019 Edition Essential oils - Analysis by gas chromatography on packed columns - General method 精油－填充管柱氣相層析法通則 |
|
|
|
CNS 12514-9
2019 Edition Fire-resistance tests – Elements of building construction – Part 9: Specific requirements for non-loadbearing ceiling elements 建築物構造構件耐火試驗法－第9 部：非承重天花板特定要求 |
|
|
|
CNS 15755-5-5
2019 Edition Conversion tables for units − Part 5-5: Pressure or stress − Millimeter of mercury and standard atmosphere 單位換算表－第5-5 部：壓力或應力－毫米汞柱與標準大氣壓 |
|
|
|
CNS 15336
2019 Edition Furniture - Method of determination for strength and durability of table 家具－桌子強度與耐久性測定法 |
|
|
|
CNS 15056
2019 Edition Fat and oil derivatives - Fatty acid methyl esters (FAME) - Determination of oxidation stability (accelerated oxidation test) 油脂衍生物（脂肪酸甲酯）－氧化穩定性測定法（加速氧化法） |
|
|
|
CNS 11633
2019 Edition Flexible Metallic Packing Material 可撓性金屬填料 |
|
|
|
CNS 15698
2019 Edition Repair of flat wooden pallets 木製平墊板維修基準 |
|
|
|
CNS 3813
2019 Edition Marine Cast Iron 10 kgf/㎠ Screw-down Check Angle Valves 船用鑄鐵旋緊止回角閥（10 kgf/㎠） |
|
|
|
CNS 15600
2019 Edition Photovoltaic devices - Procedures for temperature and irradiance corrections to measured I-V characteristics 太陽光電裝置－量測I-V特性之溫度與照射度修正程序 |
|
|
|
CNS 14545-1
2019 Edition Fire hazard testing-part 1:Guidance for assessing fire hazard of electrotechnical products(general guidance) 火災危險性試驗－第１部：評估電氣產品火災危險性的指引（通則） |
|
|
|
CNS 13785
2019 Edition Methods of Test for Synthetic Filament Textured Yarns 合成絲狀纖維加工紗試驗法 |
|
|
|
CNS 15124
2019 Edition Liquid hydrogen - Land vehicle fuelling system interface 液態氫－陸用車輛加氫系統介面 |
|
|
|
CNS 15125-2
2019 Edition Solar heating - Domestic water heating systems - Part 2 : Outdoor test methods for system performance characterization and yearly performance prediction of solar-only systems 太陽能加熱－家用熱水系統－第２部：僅用太陽能系統的性能特性與年度性能預測之室外試驗法 |
|
|
|
CNS 14840
2019 Edition Method of test for passability through obstacles of self-compacting concrete 自充填混凝土障礙通過性試驗法（Ｕ形或箱形法） |
|
|
|
CNS 10759
2019 Edition Sack kraft paper 袋用牛皮紙 |
|
|
|
CNS 16097-1
2019 Edition Machine tools − Dimensions and geometric tests for self-centring chucks with two-piece jaws − Part 1: Manually operated chucks with tongue and groove type jaws 工具機－具兩件式夾爪之自定心夾頭的尺度及幾何試驗－第1部：具榫槽式夾爪之手動操作夾頭 |
|
|
|
CNS 15716
2019 Edition Oil of turpentine, Iberian type (Pinus pinaster Sol.) 松節油(伊比利亞型) |
|
|
|
CNS 13865
2019 Edition Symbols of instruments and controls for automobiles 汽車儀表及控制器標誌 |
|
|
|
CNS 10160
2019 Edition Tolerance in Length for Wiring Harness for Automobiles 汽車用電線束長度之尺度許可差 |
|
|
|
CNS 15683
2019 Edition Standard representation of geographic point location by coordinates 地理點位置之座標標準表示法 |
|
|
|
CNS 15593-31
2019 Edition Electricity metering – Data exchange for meter reading, tariff and load control – Part 31: Use of local area networks on twisted pair with carrier signalling 電力計量－ 讀表、計費及負載控制之資料交換－ 第31 部： 使用雙絞線載波信號之區域網路 |
|
|
|
CNS 6187
2019 Edition Paints, varnishes and plastics − Determination of non-volatile-matter content 油漆、清漆及塑膠－不揮發物含量測定法 |
|
|
|
CNS 10573
2019 Edition Grades of Heng Shan Pear 橫山梨等級 |
Translated |
|
|
CNS 15125-3
2019 Edition Solar heating - Domestic water heating systems - Part 3 : Performance test for solar plus supplementary systems 太陽能加熱－家用熱水系統－第３部：太陽能加輔助系統之性能試驗法 |
|
|
|
CNS 15064-1
2019 Edition Solar energy - Reference solar spectral irradiance at the ground at different receiving conditions - Part 1: Direct normal and hemispherical solar irradiance for air mass 1.5 太陽能－在不同地球表面接收狀況下之參考太陽光譜照射度－第１部：大氣光程１﹒５下之直接垂直與半球太陽照射度 |
|
|
|
CNS 15076-2
2019 Edition Modular units for machine tools - Workholding pallets - Part 2 : Workholding pallets of nominal size greater than 800 mm 工具機之模組單元－工件固定托板－第２部：標稱尺度８００ｍｍ以上之工件固定托板 |
|
|
|
CNS 16107-1
2019 Edition Hollow taper interface with flange contact surface − Part 1: Shanks − Dimensions 具凸緣接觸面之空心錐度界面－第1部：刀柄尺度 |
|
|
|
CNS 15228-7
2019 Edition Test methods for lead-free solders - Part 7: Shear strength of solder joints on surface-mounted devices 無鉛銲錫試驗法－第７部：表面黏著元件上銲錫接點之剪力強度試驗法 |
|
| Find out:10860Items | To Page of: First -Previous-Next -Last | [106] [107] [108] [109] [110] [111] [112] |
