"6 6 " CNS Standards List| Morse Taper | Horizontal Type | Personal protective | Method Test | Chemical Reagent | Wind turbines | Gas Analysis | Lifting Hooks, | |
|
CNS 16022
2017 Edition Acoustics − Determination of dynamic stiffness − Part 1: Materials used under floating floors in dwellings 聲學－動態剛性測定法－用於住宅浮式地板下之材料 |
|
|
|
CNS 12865-7
2017 Edition Method of Test for Digital Microelectronics ( Drive Source, Dynamic ) 數位微電子檢驗法（驅動源，動態） |
|
|
|
CNS 7642
2017 Edition Method of Test for Fiber Optic Devices (Air Leakage Testing of Fiber Optic Component Seals) 光纖裝置檢驗法（光纖組件密封漏氣試驗ＦＯＴＰ–２３） |
|
|
|
CNS 16016-7
2017 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PP) − Part 5: Fitness for purpose of the system 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第7部：符合性評鑑指引 |
|
|
|
CNS 11446-4
2017 Edition Methods of measurement on receivers for television broadcast transmissions -Part 4 : Electrical measurements on multichannel sound television receivers using the two-carrier FM-system 電視廣播傳輸接收機之量測方法-第4部 : 利用雙載波調頻(FM)系統之多聲道電視接收機之電氣量測 |
|
|
|
CNS 12546
2017 Edition Gloves of insulating material used for electrical working 電氣作業用絕緣手套 |
|
|
|
CNS 9476
2017 Edition Test Code for Accuracy of Numerically Controlled Turret and Single Spindle Drilling Machines with Vertical Spindle 數值控制立式六角及單軸鑽床精度檢驗標準 |
|
|
|
CNS 6032
2017 Edition Alkaline Primary Cells and Batteries 鹼性一次電池 |
|
|
|
CNS 11446-6
2017 Edition Methods of measurement on receivers for television broadcast transmission - Part 6 : Measurement under conditions different from broadcast signal standards 電視廣播傳輸接收機之量測方法-第6部 : 不同於廣播信號標準條件之量測 |
|
|
|
CNS 6135
2017 Edition Hearing aids-Part 0:Measurement of electroacoustical characteristics 助聽器－第０部:電聲特性的量測 |
|
|
|
CNS 15562-7
2017 Edition Stationary training equipment − Part 7: Rowing machines − Additional specific safety requirements and test methods 固定式訓練設備－第7部：划船機－附加之特定安全要求與試驗法 |
|
|
|
CNS 5376-15
2017 Edition Iron ores─Methods for determination of magnesium content 鐵礦石－鎂定量法 |
|
|
|
CNS 5376-17
2017 Edition Iron ores─Methods for determination of chromium content 鐵礦石－鉻定量法 |
|
|
|
CNS 12634
2017 Edition Method of test for fruit and vegetable juice products - Determination of sugars by HPLC 水果及蔬菜汁飲料檢驗法－糖類之測定（ＨＰＬＣ法） |
|
|
|
CNS 13106
2017 Edition Methods of Test for Water Content of Chemical Products 化學製品水分測定法 |
|
|
|
CNS 7663
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 24 Maintenance Aging Test) 頻率３ＭＨｚ以下電連接器檢驗法（維護老化試驗ＴＰ–２４） |
|
|
|
CNS 2869
2017 Edition Spheroidal graphite iron castings 球狀石墨鑄鐵件 |
|
|
|
CNS 16016-5
2017 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PP) − Part 3: Fittings 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第5部：系統適合度 |
|
|
|
CNS 6135-12
2017 Edition Heading aids-Part12: Dimensions of electrical connector systems 助聽器－第12部:電氣連接系統之尺寸 |
|
|
|
CNS 5376-5
2017 Edition Iron ores—Methods for determination of total iron content 鐵礦石—總鐵定量法 |
|
|
|
CNS 5961
2017 Edition General Rules for Inspection of Valves 閥之檢驗總則 |
|
|
|
CNS 12565
2017 Edition Basic Environmental Testing Procedures Part 2: Tests, Test Db: Damp Heat, Cycle (12+12-Hour Cycle) 環境試驗方法（電氣、電子）–溫濕度循環（１２＋１２小時循環）試驗方法 |
|
|
|
CNS 9367
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 14 Ozone Exposure) 頻率３ＭＨｚ以下電連接器檢驗法（耐臭氧試驗ＴＰ–１４） |
|
|
|
CNS 5267
2017 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 6408
2017 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算–齒廓面作用帶因數Zн |
|
|
|
CNS 12561
2017 Edition Method of Test for Fiber Optic Devices (FOTP-101 Accelerated Oxygen Aging) 光纖裝置檢驗法（加速氧化老化試驗ＦＯＴＰ–１０１） |
|
|
|
CNS 12673
2017 Edition Method of Test for Free Bend of Buff Welding Joint 對接熔接縫自由彎曲試驗法 |
|
|
|
CNS 6834-6
2017 Edition Testing methods for rubber and plastics hoses - Part 6: Determination of adhesion between components 橡膠管及塑膠管試驗法－第6部：層間接著強度之測定 |
|
|
|
CNS 9960
2017 Edition Thermal insulation materials for buildings 建築用隔熱材料 |
|
|
|
CNS 9461
2017 Edition Accuracy Inspection of Knee Type Vertical - Horizontal Universal Milling Machines 膝型立臥複合萬能銑床精度檢驗標準 |
|
| Find out:5911Items | To Page of: First -Previous-Next -Last | [109] [110] [111] [112] [113] [114] [115] |
