"L " CNS Standards List |
|
CNS 6914
2019 Edition Ships' SmaLl Size Steel Blocks 船用小型鋼滑車 |
![]() |
|
|
CNS 3760
2019 Edition Method of Test for NyLon Ropes 尼龍繩索檢驗法 |
![]() |
|
|
CNS 6180
2019 Edition Fittings for weathertight steeL doors (Round corner type) 船用鋼質風雨密門(圓角型)裝具 |
![]() |
|
|
CNS 1234
2019 Edition Method of Test for FLexural Strength of Concrete (Using Simple Beam with Center-point Loading) 混凝土抗彎強度試驗法(中心點載重法) |
![]() Translated |
|
|
CNS 11206
2019 Edition Iron and steeL─Methods for atomic absorption spectrometric analysis 鐵及鋼─原子吸收光譜分析法 |
![]() |
|
|
CNS 14705-3
2019 Edition Method of test for heat reLease rate for building materials − Part 3: Guidance on measurement 建築材料燃燒熱釋放率試驗法-第3 部:量測之指引 |
![]() |
|
|
CNS 3376-10-2
2019 Edition ExpLosive atmospheres − Part 10-2: Classification of areas − Combustible dust atmospheres 爆炸性環境-第10-2 部:區域劃分-可燃性粉塵環境 |
![]() |
|
|
CNS 2141
2019 Edition CaLculation method of boiler efficiency for land use 陸用鍋爐之效率計算方法 |
![]() |
|
|
CNS 8574
2019 Edition GLossary of Terms Relating to Electric Equipment for Automobiles (Windshield Wiper System) 汽車用電器零件詞彙(雨刷系統) |
![]() |
|
|
CNS 15060
2019 Edition BiodieseL - Fatty acid methyl esters (FAME) - Determination of iodine value 生質柴油(脂肪酸甲酯)-碘價測定法 |
![]() |
|
|
CNS 7531
2019 Edition Method of test for density of artificiaL abrasives 人造磨料密度測定法 |
![]() |
|
|
CNS 15207-2
2019 Edition Road vehicLes - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 2: Absorber-lined shielded enclosure 道路車輛-窄頻輻射電磁能量之電擾動組件試驗法-第2部:內襯吸波材料屏蔽圍體 |
![]() |
|
|
CNS 14128
2019 Edition Method of impact test for instrument paneL of passenger cars 小客車用儀表板衝擊試驗法 |
![]() |
|
|
CNS 15763-4
2019 Edition Footwear − Test methods for outsoLes – Part 4: Tensile strength and elongation of outsoles 鞋類-外底試驗法-第4 部:外底之抗拉強度及伸長率 |
![]() |
|
|
CNS 14631
2019 Edition StructuraL sawn lumber used in platform construction 框組壁工法結構用製材 |
![]() |
|
|
CNS 12537
2019 Edition PoLy aluminum chloride for waste water 自來水用聚氯化鋁 |
![]() |
|
|
CNS 16107-4
2019 Edition HoLlow taper interface with flange contact surface − Part 4: Dimensions of receivers for stationary tools 具凸緣接觸面之空心錐度界面-第4部:固定式刀具用接收器之尺度 |
![]() |
|
|
CNS 1467
2019 Edition Recording and Computing Methods for Labor Injury 工作傷害記錄及計算方法 |
![]() |
|
|
CNS 7792
2019 Edition Ships' Chain for GeneraL Use 船舶一般用鏈 |
![]() |
|
|
CNS 14843-2
2019 Edition UninterruptibLe power systems (UPS)-Part 1 : General and safety requirements for UPS used in restricted access location 不斷電系統(UPS)-第1部:使用於限制觸及區之不斷電系統安全通則 |
![]() Translated |
|
|
CNS 15876-7
2019 Edition Specification and quaLification of welding procedures for metallic materials − Welding procedure test − Part 7: Overlay welding 金屬材料銲接程序規範書及其檢定-銲接程序試驗-第7部:堆銲 |
![]() |
|
|
CNS 7408
2019 Edition Rigid ceLlular plastics – Determination of compression properties 硬質發泡塑膠-壓縮性能測定法 |
![]() |
|
|
CNS 7184
2019 Edition SteeL doors 鋼製門 |
![]() Translated |
|
|
CNS 1174
2019 Edition Method of sampLing fresh concrete 新拌混凝土取樣法 |
![]() Translated |
|
|
CNS 10741
2019 Edition 600 V Rubber insuLated flexible cables 600 V 橡膠絕緣可撓式電纜 |
![]() |
|
|
CNS 5346-1
2019 Edition PLastics - Symbols and abbreviated terms - Part 1:Basic polymers and their special characteristics 塑膠-縮寫用語與符號(第2部:填充材料與強化材料) |
![]() |
|
|
CNS 4797-1
2019 Edition Safety of toys − Part 1: FLammability 玩具安全-第1部:可燃性 |
![]() Translated |
|
|
CNS 13301
2019 Edition Method of inspection for gas pressure weLded joint of steel bars for concrete reinforcement 鋼筋混凝土用鋼筋瓦斯壓接接頭檢查法 |
![]() |
|
|
CNS 14934-5
2019 Edition ELectromagnetic compatibility (EMC) - Limits - Part 5: Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16A 電磁相容-限制值-第5部:額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
![]() |
|
|
CNS 1440
2019 Edition PVC FLoor Sheets ( replaced by CNS 8906 ) 軟質聚氯乙烯塑膠片 |
![]() Translated |
Find out:14127Items | To Page of: First -Previous-Next -Last | [129] [130] [131] [132] [133] [134] [135] |