"o " CNS Standards List| Footwear − | Method test | Feed Rock | Methods Chemical | Electrically propelled | Cone proof | Method Test | Annealed Copper | |
|
CNS 12685
2019 Edition Electroplated Coatings of Chromium for Engineering Use 工程用鉻電鍍層 |
|
|
|
CNS 15187-3-1
2019 Edition Low-voltage fuses - Part 3-1: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) - SectionsⅠto IV: Examples of types of standardized fuses 低壓熔線－第３－１部︰非專業人員用熔線之補充規定（以家用及類似用途為主之熔線）－第Ｉ章至第ＩＶ章：經標準化之熔線各種類型範例 |
|
|
|
CNS 12172
2019 Edition Method of Test of Rusting at Material Interfaces for Disc Brake Pads of Automobiles 汽車用圓盤煞車襯墊接着面生銹試驗法 |
|
|
|
CNS 1389
2019 Edition Method of Test for Bast Fiber Bag 麻袋檢驗法 |
|
|
|
CNS 3086
2019 Edition Method of test for determination of moisture content in pulp, paper and board（Oven-drying method） 紙漿、紙及紙板含水率測定法（烘箱法） |
|
|
|
CNS 15722
2019 Edition Self adhesive tapes – Measurement of static shear adhesion 感壓性黏膠帶─靜態保持力量測法 |
|
|
|
CNS 15126
2019 Edition Solar energy - Water heating systems - Guide to material selection with regard to internal corrosion 太陽能－熱水系統－相關內部腐蝕材料之選擇指引 |
|
|
|
CNS 14902
2019 Edition Essential oils（containing tertiary alcohols）- Evaluation of alcohols content by determination of ester value after cold formylation 精油（含三級醇）－經冷甲醯化反應測定酯價以評估自由醇含量法 |
|
|
|
CNS 16107-1
2019 Edition Hollow taper interface with flange contact surface − Part 1: Shanks − Dimensions 具凸緣接觸面之空心錐度界面－第1部：刀柄尺度 |
|
|
|
CNS 15081
2019 Edition Neighbor discovery for IP version 6 (IPv6) 用於網際網路協定第６版（ＩＰｖ６）之鄰節點探索 |
|
|
|
CNS 9326
2019 Edition Compressed fiber jointing 壓縮墊料板 |
|
|
|
CNS 15019
2019 Edition Method of test for determination of additive elements in lubricating oils by inductively coupled plasma atomic emission spectrometry 潤滑油添加劑元素含量測定法（感應耦合電漿原子發射光譜法） |
|
|
|
CNS 8572
2019 Edition Glossary of Terms Relating to Electric Equipment for Automobiles (Charging, Starting, Ignition, Preheating System) 汽車用電器零件詞彙（充電、起動、點火、預熱系統） |
|
|
|
CNS 14498-2
2019 Edition Road vehicles - Electrical disturbances from conduction and coupling - Part 2: Electrical transient conduction along supply lines only 道路車輛－經由傳導及耦合之電擾動－第２部：僅由電源線傳導之電暫態 |
|
|
|
CNS 15590-5
2019 Edition Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners with specified hardness classes – Coarse thread and fine pitch thread 碳鋼及合金鋼結件之機械性質－第5 部：規定硬度級數之固定螺釘及類似螺紋結件－粗螺紋及細螺紋 |
|
|
|
CNS 14929-5
2019 Edition Information technology - Guidelines for the management of IT security - Part 5: Management guidance on network security 資訊技術－資訊技術安全管理指導綱要－第5部：網路安全管理指引 |
|
|
|
CNS 1494-7
2019 Edition Textiles-Colour fastness to wet scrubbing of pigment printed textiles 紡織品－顏料著色紡織品耐濕刷色牢度試驗法 |
|
|
|
CNS 6959
2019 Edition Acid and Heat Resisting Bricks for Chemical Industry 化學工業用耐酸耐熱磚 |
|
|
|
CNS 6338
2019 Edition Tungsten Wires for Lighting and Electronic Equipments 照明及電子設備用鎢線 |
|
|
|
CNS 15125-2
2019 Edition Solar heating - Domestic water heating systems - Part 2 : Outdoor test methods for system performance characterization and yearly performance prediction of solar-only systems 太陽能加熱－家用熱水系統－第２部：僅用太陽能系統的性能特性與年度性能預測之室外試驗法 |
|
|
|
CNS 2101
2019 Edition Method of Test for Shell Eggs 蛋檢驗法 |
Translated |
|
|
CNS 16080
2019 Edition Safety of primary and secondary lithium cells or batteries during transport − Test methods and requirements 一次及二次鋰單電池或電池組之運輸安全－試驗法與要求 |
|
|
|
CNS 14964-25
2019 Edition Wheelchairs − Part 25: Batteries and chargers for powered wheelchairs 輪椅－第25 部：電動輪椅之電池組及充電器 |
|
|
|
CNS 15660-3
2019 Edition Test conditions for numerically controlled turning machines and turning centres − Part 3: Geometric tests for machines with inverted vertical workholding spindles 數值控制車床及車削中心機之試驗條件－ 第3部：倒立式工件夾持主軸工具機之幾何試驗 |
|
|
|
CNS 10982
2019 Edition Aluminium Alloy Castings for Bearing 軸承用鋁合金鑄件 |
|
|
|
CNS 15683
2019 Edition Standard representation of geographic point location by coordinates 地理點位置之座標標準表示法 |
|
|
|
CNS 15666
2019 Edition Long durable top coats for constructions 建築用長期耐候性面漆 |
|
|
|
CNS 15014-6
2019 Edition Software engineering - Product evaluation - Part 6：Documentation of evaluation modules 軟體工程－產品評估－第６部：評估模組的文件製作 |
|
|
|
CNS 8112
2019 Edition Marine Cast Steel Globe Valves for Compressed Air 船用鑄鋼壓縮空氣球形閥 |
|
|
|
CNS 15077-1
2019 Edition Test conditions for machining centers - Part 1 : Geometric tests for machines with horizontal spindle and with accessory heads (horizontal Z-axis) 切削中心機之檢驗條件－第１部：具水平主軸與附屬頭之幾何檢驗（水平Ｚ軸） |
|
| Find out:15086Items | To Page of: First -Previous-Next -Last | [152] [153] [154] [155] [156] [157] [158] |
