"1 " CNS Standards List |
|
CNS 14839
2018 Edition Packaging – Complete, filled transport packages and unit loads – Water-spray test 包裝貨物與單位裝載之灑水試驗法 |
|
|
|
CNS 14211
2018 Edition Broadband-ISDN, interworking between signalling system No.7 broadband ISDN user part (B-ISUP) and digital subscriber signalling system No.2 (DSS 2) 寬頻整體服務數位網路–第七號信號系統之寬頻整體服務數位網路使用者部與第二號數位用戶信號系統間互作 |
|
|
|
CNS 13713
2018 Edition Functional Description of the Message Transfer Part (MTP) Level 2 of Signalling System No.7 第七號信號系統訊息轉送部第２階功能描述 |
|
|
|
CNS 15703-2
2018 Edition Tool shanks with 7/24 taper for automatic tool changers – Part 2: Dimensions and designation of shanks of forms J, JD and JF 自動換刀器用7/24 錐度刀柄－第2 部：刀柄型式J、JD 及JF 之尺度及標示 |
|
|
|
CNS 4971
2018 Edition Method of Test for Boxes for Unplasticized Polyvinyl Chloride (UPVC) Conduit 硬質聚氯乙烯電氣接線盒檢驗法 |
Translated |
|
|
CNS 15691-1
2018 Edition Aseptic processing of health care products − Part 1: General requirements 健康照護產品之無菌操作－第 1 部:一般要求 |
|
|
|
CNS 15691-2
2018 Edition Aseptic processing of health care products − Part 2: Filtration 健康照護產品之無菌操作－第 2 部:過濾 |
|
|
|
CNS 4394-2
2018 Edition Plastics − Injection moulding of test specimens of thermoplastic materials − Part 1: General principles, and moulding of multipurpose and bar test specimens 塑膠－熱塑性塑膠射出成型試片－第2部：小型拉伸試驗棒 |
|
|
|
CNS 11010
2018 Edition Electric storage tank water heaters 貯備型電熱水器 |
Translated |
|
|
CNS 10062
2018 Edition Nominal Dimension of Veneer Jointers 薄板刨邊機之標稱尺度 |
|
|
|
CNS 18080-2
2018 Edition Textiles − Test methods for evaluating the electrostatic propensity of fabrics − Part 2: Test method using rotary mechanical friction 紡織品－靜電性評估法－ 第2部：旋轉機械摩擦試驗法 |
|
|
|
CNS 11321
2018 Edition Method of Test for Absorption and Bulk Specific Gravity of Natural Building Stone 建築用天然石吸水率及體比重試驗法 |
|
|
|
CNS 11202
2018 Edition Axle Boxes for Railway Rolling Stock 鐵路車輛用軸箱 |
|
|
|
CNS 14737
2018 Edition B-ISDN user part - Support of additional traffic parametersfor sustainable cell rate and quality of service 寬頻整體服務數位網路使用者部－可維持的細胞速率和服務品質之附加訊務參數的支援 |
|
|
|
CNS 12050
2018 Edition Heat resistant glass wares 耐熱玻璃製食品器具 |
|
|
|
CNS 1910
2018 Edition Pylon Slalom Test Procedure for Passenger Car and Light Trailer Combination 吡啶（試藥） |
|
|
|
CNS 15569-6
2018 Edition Hydraulic fluid power - Filters elements - Part 6: Evaluation of differential pressure versus flow characteristics 液壓流體動力－過濾器濾心－第6部：差壓對流動特性之評估 |
|
|
|
CNS 1134
2018 Edition Pliers and nippers - End cutting nippers 夾鉗與剪鉗－工程及配線用鉗（老虎鉗） |
|
|
|
CNS 14952-3-1
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials - Part 3: Instructions for calculating thermal endurance characteristics - section 1: calculations using mean values of normally distributed complete data 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第１章：利用常態分配完整資料的平均值進行計算 |
|
|
|
CNS 2183
2018 Edition Polyester Canvas 聚酯漆包銅線 |
Translated |
|
|
CNS 15620-2-1
2018 Edition Insulation coordination for equipment within low-voltage system – Part 2-1: Application Guide – Dimensioning procedure worksheets and dimensioning examples 低電壓系統下設備之絕緣協調－第2-1 部： 應用指引－ 尺寸量測程序工作表及尺寸量測範例 |
|
|
|
CNS 16090
2018 Edition Test methods for interconnection protocol for devices in smart home 智慧家庭之裝置互連協定測試法 |
|
|
|
CNS 5315
2018 Edition The Test Methods of Panel Board Units 配電箱試驗法 |
|
|
|
CNS 14225
2018 Edition Lower layer protocol profiles for the Q3 interface 用於Ｑ３介面的低層協定規範 |
|
|
|
CNS 14952-3-2
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials – Part 3: Instructions for calculating thermal endurance characteristics – section 2: the calculation for incomplete data – verification for test result from gr 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第２章：不完整資料的計算－以包含中間時間到終止點之等量試驗群組驗證試驗結果 |
|
|
|
CNS 10273-2
2018 Edition Rubber, unvulcanized − Determination using a shearing-disc viscometer − Part 2: Determination of pre-vulcanization characteristics 未硫化橡膠－使用剪力-圓盤型黏度計測定－第2部：早期硫化特性 |
|
|
|
CNS 15155
2018 Edition Biological evaluation of medical devices - Part 19 : Physico-chemical, morphological and topographical characterization of materials 醫療器材生物性評估－第１９部：材料之物理化學、形態及拓撲學的特性分析 |
|
|
|
CNS 9716
2018 Edition Method of Test for Liquid Unsaturated Polyester Resin 液狀不飽和聚酯樹脂檢驗法 |
Translated |
|
|
CNS 14989
2018 Edition Medical devices - Application of risk management to medical devices 醫療器材風險管理 |
|
|
|
CNS 10855
2018 Edition Criteria for Selection of Plastics Used for Marine Electrical Appliances 船用電器塑膠選用準則 |
|
| Find out:10860Items | To Page of: First -Previous-Next -Last | [163] [164] [165] [166] [167] [168] [169] |
