"R " CNS Standards List| Method test | Water cooled | Classification Dimensions | Glossary Terms | Engineering drawing | Nominal Dimension | Navigation Light | Rigid cellular | |
|
CNS 5321
2019 Edition Mounting Dimensions of StaRting Motors for Automobiles 汽車用起動電動機安裝尺度 |
|
|
|
CNS 15327-5
2019 Edition InfoRmation technology − Automatic identification and data capture techniques − Unique identification − Part 5: Individual returnable transport items (RTIs) 資訊技術－自動識別及資料擷取技術－唯一識別－第5部：個別可退還運送品項 |
|
|
|
CNS 3483
2019 Edition Method of test foR Saybolt viscosity of petroleum products 石油產品賽氏黏度試驗法 |
|
|
|
CNS 11991
2019 Edition Method of test foR joint treatment materials for gypsum boards 石膏板用接縫處理材料檢驗法 |
|
|
|
CNS 9246
2019 Edition CoRnering Performance Test Procedure for Passenger Car and Light Trailer Combinations 小客車與輕拖車連結時迴轉性能試驗法 |
|
|
|
CNS 15158
2019 Edition Textual conventions foR IPv6 flow label ＩＰｖ６訊流標籤之文字規約 |
|
|
|
CNS 11414
2019 Edition Method of Chemical Analysis foR Tungsten and Molybdenum Material 鎢鉬材料分析法 |
|
|
|
CNS 15763-5
2019 Edition FootweaR − Test methods for outsoles – Part 5: Determination of split tear strength and delamination resistance of outsoles 鞋類－外底試驗法－第5 部：外底之剝離撕裂強度及耐層間剝離性的測定 |
|
|
|
CNS 14901
2019 Edition Essential oils - GeneRal rules for labelling and marking of containers 精油－容器標籤與標示通則 |
|
|
|
CNS 2939
2019 Edition Polyethylene pipes foR water works ( replaced by CNS 2456-1, CNS 2456-2, CNS 2456-3, CNS 2456-5 ) 聚乙烯樹脂 |
Translated |
|
|
CNS 13561
2019 Edition Method of Test foR Grains-Brabender Amylography(2) 穀類檢驗法–布氏（Ｂｒａｂｅｎｄｅｒ）連續黏度法（二） |
|
|
|
CNS 3489
2019 Edition PolyacRylonitrile Spun Yarns, Cotton System, Unfinished Regular Yarn 聚丙烯腈棉狀纖維（非收縮型） |
Translated |
|
|
CNS 15565-3
2019 Edition ERgonomic design for the safety of machinery – Part 3: Anthropometric data 機械安全之人因工程設計－第3部：人體計測數據 |
|
|
|
CNS 8072
2019 Edition Movable paRtition 活動隔牆 |
|
|
|
CNS 10573
2019 Edition GRades of Heng Shan Pear 橫山梨等級 |
Translated |
|
|
CNS 546
2019 Edition 300 V Rubber insulated cords 300 V 橡膠絕緣花線 |
|
|
|
CNS 13059-4
2019 Edition Photovoltaic devices - PaRt 4: Reference solar devices - Procedures for establishing calibration traceability 太陽光電裝置－第4部：基準太陽 裝置－建立校正追溯性之程序 |
|
|
|
CNS 10272
2019 Edition Method of Specimens PReparation for Physical Properities Test of Unvulcanized Rubber 未硫化橡膠物理性能檢驗之試片製作方法 |
|
|
|
CNS 15733-3
2019 Edition Communication netwoRks and systems in substations – part 3: General requirements 變電所通訊網路及系統－第3 部：一般要求事項 |
|
|
|
CNS 15755-5-3
2019 Edition ConveRsion tables for units − Part 5-3: Pressure or stress − Kilogram-force per square millimeter and U.S. ton force per square inch 單位換算表－第5-3 部：壓力或應力－公斤力每平方毫米與美噸力每平方英寸 |
|
|
|
CNS 11735
2019 Edition Method of Test foR Refined Fish Liver Oil 精製水產物肝油檢驗法 |
|
|
|
CNS 15781-2
2019 Edition MeasuRement of smoke density of cables burning under defined conditions − Part 2: Test procedure and requirements 電(光)纜於特定條件下燃燒之煙密度量測－第2 部：試驗程序及要求 |
|
|
|
CNS 13059-7
2019 Edition Photovoltaic devices - PaRt 7: Computation of the spectral mismatch correction for measurements of photovoltaic devices 太陽光電裝置－第7部：太陽光電裝置量測之光譜不匹配修正計算 |
|
|
|
CNS 12912
2019 Edition Method of Test foR Tungsten in Nickel Materials for Electron Tubes 電子管用鎳材料中鎢檢驗法 |
|
|
|
CNS 2349
2019 Edition Plugs,telephone (Type PJ-309) and accessoRy screws 李 |
Translated |
|
|
CNS 19028
2019 Edition Accessible design − InfoRmation contents, figuration and display methods of tactile guide maps 無障礙設計－觸覺導引地圖之訊息內容、形狀及顯示法 |
|
|
|
CNS 11450
2019 Edition Steel-Method foR determination of tantalum content 鋼─鉭定量法 |
|
|
|
CNS 15634
2019 Edition Method of test foR change in height at early ages of cylindrical specimens of cementitious mixtures 膠結拌成物圓柱試體早期高度變化測定法 |
|
|
|
CNS 2386
2019 Edition PapeR napkin 紙餐巾 |
|
|
|
CNS 3672
2019 Edition Dimensions of tyRes for truck and bus 卡車及客車用輪胎尺度 |
Translated |
| Find out:15408Items | To Page of: First -Previous-Next -Last | [184] [185] [186] [187] [188] [189] [190] |
