"1,5 " CNS Standards List| General Rules | Planer Knives | Method test | Method Test | Methods measurement | Textiles | Test methods | Method Test | |
|
CNS 7563
2021 Edition Flat Round Head Rivets Nominal Diameters 1.4 to 6 mm 扁圓頭鉚釘（標稱直徑１．４至６ｍｍ） |
|
|
|
CNS 15489-2
2021 Edition Information and documentation - Records management - Part 2: Guidelines 資訊與文獻－檔案管理－第２部：指導綱要 |
|
|
|
CNS 15498
2021 Edition Methods of measurement on light emitting diode modules for thermal resistance 發光二極體模組之熱阻量測法 |
|
|
|
CNS 15831
2021 Edition Zinc rich primer 富鋅底漆 |
|
|
|
CNS 12658
2021 Edition Clossary of Terms Used for Apparel ( Measuring Part ) 服飾詞彙（量測部分） |
|
|
|
CNS 15369-1
2021 Edition Secondary batteries for the propulsion of electric road vehicles – Part 1: Test parameters 電動車輛推進用二次電池組－第1部：試驗參數 |
|
|
|
CNS 5196
2021 Edition Neon Glow Lamp 霓虹指示燈泡 |
|
|
|
CNS 15875-1
2021 Edition Ergonomics of the thermal environment –Methods for the assessment of human responses to contact with surfaces –Part 1: Hot surfaces 熱環境之人因工程－人體接觸表面之反應評鑑方法－第1 部：熱表面 |
|
|
|
CNS 15310
2021 Edition Steel slag aggregates for bituminous paving mixtures 瀝青鋪面混合料用鋼爐碴粒料 |
|
|
|
CNS 3651
2021 Edition Method of test for edible oils and fats－Cloud point test 食用油脂檢驗法－混濁點之測定 |
|
|
|
CNS 60335-2-102
2021 Edition Household and similar electrical appliances − Safety − Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections 家用和類似用途電器－安全性－第2-102 部：具電氣連接之氣體、燃油及固態燃料燃燒電器之個別規定 |
|
|
|
CNS 15628-2
2021 Edition Wheelchair seating − Part 2: Determination of physical and mechanical characteristics of seat cushions intended to manage tissue integrity 輪椅乘坐系統－第2部：維持組織完整性座墊之物理與機械特性的測定 |
|
|
|
CNS 12150
2021 Edition Method of Test for Sport Drinks 運動飲料檢驗法 |
Translated |
|
|
CNS 14232-5
2021 Edition Health Level Seven (HL7) - Part 5: Query 健康資訊交換第七層協定－第５部：查詢 |
|
|
|
CNS 12145
2021 Edition Varnish for interior wooden floor 室內用木質地板清漆 |
|
|
|
CNS 15917
2021 Edition Polyethylene large diameter profile wall sewer and drain pipe 聚乙烯塑膠管－耐慢速裂痕擴展－錐體試驗法 |
|
|
|
CNS 12835-2
2021 Edition Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 1: General 燃氣用塑膠配管系統－聚乙烯(PE)－第２部：管 |
|
|
|
CNS 15886
2021 Edition Cycles − Hubs and freewheels − Assembly dimensions 自行車－輪轂與飛輪－總成尺度 |
|
|
|
CNS 15309
2021 Edition Fine aggregate for bituminous paving mixtures 瀝青鋪面混合料用細粒料 |
|
|
|
CNS 5016
2021 Edition High Speed Steel Tool Bits 高速鋼刀具塊 |
|
|
|
CNS 15939
2021 Edition Leather − Chemical tests − Preparation of chemical test samples 皮革－化性測試－試樣製備 |
|
|
|
CNS 12805
2021 Edition Method of break test for fillet welded joint 填角銲接接頭之斷裂試驗法 |
|
|
|
CNS 5965
2021 Edition Bronze Screwed Angle Valves (10kgf/c㎡) 青銅螺紋口角閥（10 kgf/㎠） |
|
|
|
CNS 15784-1
2021 Edition Low-voltage electrical installations − Part 1: Fundamental principles, assessment of general characteristics, definitions 低電壓電機裝備－第1 部：基本原則、一般特性之評估及定義 |
|
|
|
CNS 15834
2021 Edition Road marking performance for road users 道路標線使用性能 |
|
|
|
CNS 15866
2021 Edition Oil of celery seed (Apium graveolens L.) 芹菜子油 |
|
|
|
CNS 15844
2021 Edition Oil of bitter orange (Citrus aurantium L.) 苦橙油 |
|
|
|
CNS 14572
2021 Edition Corrugated polyethylene pipe 聚乙烯波紋管 |
|
|
|
CNS 12555
2021 Edition Method of test for solar water heater for dwelling 住宅用太陽能熱水器試驗法 |
|
|
|
CNS 15511-21-2
2021 Edition Electric vehicle conductive charging system − Part 21-2: Electric vehicle requirements for conductive connection to an AC/DC supply − EMC requirements for off-board electric vehicle charging systems 電動車輛傳導式充電系統－第21-2部：電動車輛以傳導式連接至交流/直流電源的要求－非車載電動車輛充電系統的電磁相容要求 |
|
| Find out:4589Items | To Page of: First -Previous-Next -Last | [14] [15] [16] [17] [18] [19] [20] |
