"mechanical " CNS Standards List |
|
CNS 4234-3
2018 Edition mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress 不銹鋼結件之機械性質－第３部：無拉應力下之固定螺釘及類似結件 |
|
|
|
CNS 16031-3
2018 Edition Outdoor furniture − Seating and tables for camping, domestic and contract use − Part 3: mechanical safety requirements and test methods for tables 戶外家具－露營、家用及公共場所用桌椅－第3部：桌子之機械安全要求與試驗法 |
|
|
|
CNS 60715
2018 Edition Dimensions of low-voltage switchgear and controlgear − Standardized mounting on rails for mechanical support of switchgear, controlgear and accessories 低電壓開關裝置及控制裝置之尺度－為開關裝置、控制裝置及配件提供機械性支撐並達成標準化安裝之導軌 |
|
|
|
CNS 7081
2018 Edition Leads for mechanical pencils 自動鉛筆用筆芯 |
|
|
|
CNS 15041-3
2018 Edition Non-invasive sphygmomanometers - Part 3: Supplementary requirements for electro-mechanical blood pressure measuring system 非侵入式血壓計－第３部：機電式血壓量測系統的補充規定 |
|
|
|
CNS 15590-7
2018 Edition mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 16031-2
2018 Edition Outdoor furniture − Seating and tables for camping, domestic and contract use − Part 2: mechanical safety requirements and test methods for seating 戶外家具－露營、家用及公共場所用桌椅－第2部：椅子之機械安全要求與試驗法 |
|
|
|
CNS 18080-2
2018 Edition Textiles − Test methods for evaluating the electrostatic propensity of fabrics − Part 2: Test method using rotary mechanical friction 紡織品－靜電性評估法－ 第2部：旋轉機械摩擦試驗法 |
|
|
|
CNS 15041-2
2018 Edition Specification for non-invasive sphygmomanometers - Part 2: Supplementary requirements for mechanical sphygmomanometers 非侵入式血壓計－第２部：機械式血壓計之補充規定 |
|
|
|
CNS 10687
2018 Edition Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serical Binary Data Interchange-Interface mechanical Chapacteristics 資料終端設備與資料電路終端設備間互換用串列二進資料之介面–介面機械特性 |
|
|
|
CNS 15176-13
2018 Edition Wind turbines - Part 13: Measurement of mechanical loads 風力機－第13部：機械負載量測 |
|
|
|
CNS 14502
2018 Edition Steel and steel products − Location and preparation of samples and test pieces for mechanical testing 鋼及鋼製品－機械試驗用供試樣及試片之採樣位置和製備 |
|
|
|
CNS 15547-1
2018 Edition mechanical vibration and shock - Evaluation of human exposure to whole-body vibration - Part 1: General requirements 機械振動與衝擊－人體曝露於全身振動的評估－第1部：一般要求 |
|
|
|
CNS 15547-2
2018 Edition mechanical vibration and shock – Evaluation of human exposure to whole-body vibration – Part 2: Vibration in buildings (1 Hz to 80 Hz) 機械振動與衝擊－人體曝露於全身振動的 評估－第2部：建築物內的振動(1Hz～80Hz) |
|
|
|
CNS 14163-1
2018 Edition Information technology - High-performance parallel interface - Part 1: mechanical, electrical, and signalling protocol specification (HIPPI-PH) 資訊技術–高效能並行介面–第１部：機械、電氣及信號協定規格 |
|
|
|
CNS 3935
2017 Edition Method of Test for mechanical Properties of Bolts, Screws and Studs 螺栓螺釘螺樁之機械性質檢驗法 |
Translated |
|
|
CNS 6151
2017 Edition Method of Test for Electromechanical Switches(Overload) 電機開關檢驗法–過負荷 |
|
|
|
CNS 6155
2017 Edition Method of Test for Electromechanical Switches(Actuator/Mounting Bushing Resistance) 電機開關檢驗法–主動器、裝架襯套電阻值 |
|
|
|
CNS 6150
2017 Edition Method of Test for Electromechanical Switches(Terminal Temperature Rise) 電機開關檢驗法–端子溫度上昇 |
|
|
|
CNS 6158
2017 Edition Method of Test for Electromechanical Switches(Sand and Dust) 電機開關檢驗法–沙及灰塵 |
|
|
|
CNS 6153
2017 Edition Method of Test for Electromechanical Switches(Mechanical Endurance) 電機開關檢驗法–機械耐久性 |
|
|
|
CNS 6154
2017 Edition Method of Test for Electromechanical Switches(High/Low Temperature Operation) 電機開關檢驗法–高低溫操作 |
|
|
|
CNS 6147
2017 Edition Method of Test for Electromechanical Switches(Switch Resistance) 電機開關檢驗法–開關電阻值 |
|
|
|
CNS 4232
2017 Edition Torque Type Steel Hexagon Locknuts-mechanical and Performance Properties 扭矩式六角防鬆鋼螺帽之機械性能及性質 |
|
|
|
CNS 6156
2017 Edition Method of Test for Electromechanical Switches [Shock Test (Specified Pulse)] 電機開關檢驗法–指定脈衝震動 |
|
|
|
CNS 11101
2017 Edition Method of Test for Electromechanical Switches-Transmittancy (Luminance) 電機開關檢驗法–傳導度（亮度） |
|
|
|
CNS 15481-3
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 3: mechanical loads 道路車輛－電機電子配備環境條件與試驗－第３部：機械負載 |
|
|
|
CNS 6152
2017 Edition Method of Test for Electromechanical Switches(Electrical Endurance) 電機開關檢驗法–電耐久性 |
|
|
|
CNS 4316
2017 Edition mechanical Properties of Nuts-Effective Height of Thread < 0.4 d) 螺帽之機械性質（有效螺紋長度未滿０．４ｄ者） |
|
|
|
CNS 12081
2017 Edition Method of Test for Fiber Optic Devices (FOPT-13 Visual and mechanical Inspection of Fibers,Cables,Connectors and Other Fiber Optic Devices) 光纖裝置檢驗法（光纖、光纜、連接器及其他光纖裝置之目視及機械檢查ＦＯＴＰ–１３） |
|
| Find out:149Items | To Page of: First -Previous-Next -Last | 1 2 3 4 5 |
