"M " CNS Standards List |
|
CNS 127
2017 Edition Metric Taper Gauge, with Flat Head 公制圓錐量規（有扁頭） |
|
|
|
CNS 3093
2017 Edition CeMented Carbide Dies for Drawing Wires and Rods 超硬合金抽線模 |
|
|
|
CNS 10839
2017 Edition ChroMaticity Classification of Fluorescent Lamps 螢光燈管之色度分類 |
|
|
|
CNS 4363
2017 Edition Slotted Countersunk (Flat) Head Screws for Fine Mechanics M 0.4 to M 1.4 精密用有槽平頂埋頭螺釘（標稱直徑自0.4mm至1.4mm） |
|
|
|
CNS 15551-2
2017 Edition ErgonoMics - Accessible design - Sound pressure levels of auditory signals for consumer products 人因工程－無障礙設計 - 消費 產品中聲音訊號之聲壓位準 |
|
|
|
CNS 15623
2017 Edition Paragliding equipMent – Emergency parachutes – Safety requirements and test methods 飛行傘設備－緊急降落傘－安全要求與試驗法 |
|
|
|
CNS 4222
2017 Edition Metric Trapezoidal Screw Thread (Limits for Internal Screw Threads from 105 mm to 300 mm) 梯形螺紋（標稱直徑１０５ｍｍ至３００ｍｍ的內螺紋限界尺寸） |
|
|
|
CNS 13621
2017 Edition PolyaMide (Nylon) Textured Yarns 聚醯胺樹脂接線盒 |
Translated |
|
|
CNS 1432
2017 Edition Inner tubes for autoMobile tyres 汽車用內胎 |
|
|
|
CNS 14659
2017 Edition Acoustics - DeterMination of sound power levels of noise sources using sound pressure - Comparison method in situ 聲學─利用聲壓測定噪音源聲功率位準─現場的比較法 |
|
|
|
CNS 15499-2
2017 Edition Electrically propelled road vehicles – Safety specifications – Part 2: Vehicle operational safety Means and protection against failures 電動推進道路車輛－安全規範－第2部:車輛操作安全方法及故障防護 |
|
|
|
CNS 12865-9
2017 Edition Method of Test for Digital Microelectronics ( Delay Measurements ) 數位微電子檢驗法（延遲量測） |
|
|
|
CNS 660
2017 Edition Method of Test for Head Loss of Water Pumps 水泵工作位差檢驗法 |
|
|
|
CNS 7999
2017 Edition Oil TeMpered Chromium Silicon Alloy Steel Wires for Valve Springs 閥彈簧用油回火矽鉻合金鋼鋼線 |
|
|
|
CNS 67
2017 Edition DiMensions of Driving Squares and Shanks for Rotating Tools 旋轉刀具之方頭尺度及其柄徑 |
|
|
|
CNS 4578
2017 Edition Bolted Connections with Reduced Booy; Metric Thread with Large Clearence, Nominal Values and Limits 減徑柄螺栓之結合法–具大間隙之公制螺紋（標稱尺寸與限界尺寸） |
|
|
|
CNS 15077-10
2017 Edition Test conditions for Machining centres - Part 10: Evaluation of thermal distortions 切削中心機之檢驗條件－ 第10部：熱變形之評估 |
|
|
|
CNS 14623-2
2017 Edition Sterilization of health care products-cheMical indicators-Part 2：Test equipment and methods 保健產品之滅菌─化學指示劑─第二部分：測試設備與方法 |
|
|
|
CNS 14613
2017 Edition 1800 MHz GSM mobile telephone system - Air interface １８００ＭＨｚＧＳＭ行動電話系統－空中介面 |
|
|
|
CNS 13068
2017 Edition Methods of test for total amine values of amine-based hardeners of epoxy resins 環氧樹脂之胺系硬化劑總胺價試驗法 |
Translated |
|
|
CNS 12291
2017 Edition General Rules for Reliability Assured Fixed Carbon CoMposition Resistors 可靠度保證混合碳固定電阻器總則 |
|
|
|
CNS 407
2017 Edition SyMbols of Transformers 變壓器符號 |
|
|
|
CNS 517
2017 Edition Metric Buttress Screw Thread, Allowance and Tolerance 公制鋸齒形螺紋（裕度及公差） |
|
|
|
CNS 5666
2017 Edition Spindle Noses for Milling Machines 銑床主軸鼻端 |
|
|
|
CNS 502
2017 Edition ISO Metric Fine Screw Threads (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5（ISO制）（標稱直徑12至80公釐，螺距1.5公釐） |
|
|
|
CNS 10216
2017 Edition Glossary of terMs used in pressure vessels 壓力容器之用詞 |
|
|
|
CNS 5668
2017 Edition Draw - in Bolt End for Milling Machine Arbors 銑刀心軸螺栓端部 |
|
|
|
CNS 15995
2017 Edition Rubber hoses and hose asseMblies for liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas up to 25 bar (2.5 MPa) 2.5 MPa以下液相或氣相液化石油氣 (LPG)及天然氣用橡膠管及橡膠管組合件 |
|
|
|
CNS 3453
2017 Edition Method of test for milk and milk products - Test of the residual antimicrobial substances in raw milk 乳品檢驗法－生乳中抗生物質殘留之檢驗 |
|
|
|
CNS 13064
2017 Edition Methods of Test for Specific Gravity of Epoxy Resins and Hardeners 環氧樹脂及硬化劑比重測定法 |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [267] [268] [269] [270] [271] [272] [273] |
