"M " CNS Standards List |
|
CNS 13059-9
2017 Edition Photovoltaic devices Part 9: Solar siMulator performance requirements 光電伏打元件（第九部：太陽模擬器之性能要求） |
|
|
|
CNS 13394
2017 Edition Method of Test for Viscosity of Pulp (Falling Ball Method) 紙漿黏度試驗法（落球法） |
Translated |
|
|
CNS 501
2017 Edition ISO Metric Fine Screw Threads (Diameters From 8 to 30mm and Pitches 1 to 1.25mm) 公制細螺紋4（ISO制）（標稱直徑8至30公釐，螺距1至1.25公釐） |
|
|
|
CNS 1098
2017 Edition LuMbar Saws for Carpenter 木工用腰鋸 |
|
|
|
CNS 12986
2017 Edition Sizes of UntriMmed Paper 裁切前原紙尺度 |
Translated |
|
|
CNS 10114
2017 Edition Method for Determining Iron Content in Natural and Artificial Cryolite (1,10-Phenanthroline Photometric Method) 天然及人造冰晶石中鐵定量法（二氮雜菲吸光光度法） |
|
|
|
CNS 4660
2017 Edition ToMmy Nuts with Fixed Clamping Bolt 貫頭螺帽（固定扳桿型） |
|
|
|
CNS 3898
2017 Edition Canned abalone Mushroom 鮑魚菇罐頭 |
|
|
|
CNS 5517
2017 Edition CoMpression Terminals 壓縮端子 |
|
|
|
CNS 13198
2017 Edition Fixed Multilayer Ceramic Chip Capacitors for Use in Electronic Equipment 電子設備用固定多層陶瓷晶片電容器 |
|
|
|
CNS 10993
2017 Edition Methods of Testing Preformed Expansion Joint Fillers for Concrete (Nonextruding and Resilient Types) 混凝土伸縮縫預製填縫物試驗法（凹式） |
|
|
|
CNS 12085
2017 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求ＦＯＴＰ–５４） |
|
|
|
CNS 6004
2017 Edition Agricultural Tactors and Machines-Symbols for Operator Controls 農業機械之操作標示符號 |
|
|
|
CNS 16015-1
2017 Edition Transportation of dangerous goods − Part 1: RequireMent for the construction and testing of packagings 危險貨物之運輸－第1部：包裝物之構造與試驗要求 |
|
|
|
CNS 6305
2017 Edition Test Code for Accuracy of Feed Carriages of Band Saw Mills 帶鋸機進給溜板精度檢驗標準 |
|
|
|
CNS 4320
2017 Edition Hexagon Head Bolts, Finished and SeMi-Finished, Metric Fine Thread 六角頭螺栓（精製及半精制，公制細螺紋） |
|
|
|
CNS 5501
2017 Edition Self - Aligning Ball Bearings: Wide Inner Race, Inner Race with ClaMping Sleeve 自動對位滾珠軸承（具加寬內環及附夾緊套筒內環） |
|
|
|
CNS 4790-3
2017 Edition Glossary of terMs used in pulp and paper industry ─ General terms of paper and board 紙漿與紙詞彙─紙與紙板一般名詞 |
|
|
|
CNS 14492-3
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part3:Receivers for amplitude-modulated sound-broadcasting emissions 不同發射類別之無線電接收機的量測方法-第3部:調幅聲音廣播發射適用的接收機 |
|
|
|
CNS 14182
2017 Edition Reliability and lot control tests for analog video laser transMitter and receiver modules used for optical fiber communication 光纖通信用類比視訊雷射傳輸和接收模組之可靠度及批品質控制測試 |
|
|
|
CNS 11582
2017 Edition Method of Test for Epoxy Resin Non-Zinc Primer 環氧樹脂非鋅底漆檢驗法 |
|
|
|
CNS 4762
2017 Edition Method of 5 Percent Sulfuric Acid Test for Stainless Steels 不銹鋼之５％硫酸腐蝕試驗法 |
|
|
|
CNS 6142
2017 Edition Preferred Horizontal DiMensions for Industrialized Buildings 較佳值 |
|
|
|
CNS 11830
2017 Edition Measuring Methods for Light Emitting Diodes (for Indication) 發光二極體(指示用)測量法 |
|
|
|
CNS 13649
2017 Edition Reliability Testing for Laser Diode(for CoMmunication) 通信用雷射二極體之可靠度測試 |
|
|
|
CNS 1394
2017 Edition CeMet Sack Paper 水泥袋紙 |
Translated |
|
|
CNS 14368
2017 Edition Micrographics-Recommendations for the creation of original documents 微縮技術－製作原始文件的建議 |
|
|
|
CNS 10001
2017 Edition SeaMless Nickel-Chromium-Iron Alloy Tubes for Heat Exchanger 熱交換器用無縫鎳鉻鐵合金管 |
|
|
|
CNS 5492
2017 Edition Thread Take-up Levers (Link Type) of Sewing Machines for Inoustrial Use 工業用縫紉機連桿式挑線桿 |
|
|
|
CNS 7661
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 22 Life Test) 頻率３ＭＨｚ以下電連接器檢驗法（壽命試驗ＴＰ–２２） |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [278] [279] [280] [281] [282] [283] [284] |
