"or " CNS Standards List| Electric motor | Combustion Test | Drive Chain | Electricity metering | Cross Recesses | Needle Bars | Child use | Glossary Terms | |
|
CNS 11071
1984 Edition Emission-Spectroscopic Analysis for Carbon Steel and Low Alloy Steel 碳鋼及低合金鋼之發光光譜分析法 |
||
|
CNS 11072
1984 Edition Method of X-Ray Fluorescence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光X射線分析法 |
||
|
CNS 10786
1984 Edition Test Code for Performance of Drum Sanders 圓筒砂光機動態檢驗法 |
||
|
CNS 11112
1984 Edition Methods of Chemical Analysis for Lead Ingot 鉛錠分析法 |
||
|
CNS 10761
1984 Edition Method of Test for Surface Wax on Waxed Paper or Paperboard 蠟紙及蠟紙板之表面蠟量試驗法 |
Translated |
|
|
CNS 11153
1984 Edition Method of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒(空)主要尺寸 |
||
|
CNS 11157
1984 Edition Lubrication Holes, Grooves and Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
||
|
CNS 11158
1984 Edition Tungsten-Carbide Bits and Rod for Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
||
|
CNS 11159
1984 Edition Tungsten-Carbide Tip Core Drills 碳化鎢鑽刃留心鑽頭 |
||
|
CNS 5022
1984 Edition Thyristorstack for Welding Machine 電焊機用閘流調節器 |
Translated |
|
|
CNS 4731
1984 Edition Knurled Nuts for Drawing Instruments 滾紋螺帽(製圖儀器用) |
||
|
CNS 2388
1984 Edition Method of Test for Combustion Rate of Cigarette Paper 捲菸紙燃燒率試驗法 |
Translated |
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽(長型封閉式,嵌於塑膠製品與壓鑄件內用) |
||
|
CNS 4664
1984 Edition Closed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽(封閉式,嵌於塑膠製品內) |
Translated |
|
|
CNS 4663
1984 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽(片封式,嵌於塑膠製品內) |
||
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽(嵌於塑膠製品內) |
||
|
CNS 5298
1984 Edition Hose Clamps for the Lower Pressure 低壓軟管夾 |
||
|
CNS 11091
1984 Edition Measuring Projectors 投影檢測機 |
||
|
CNS 5266
1984 Edition Series of Modules for Worm Gear Pairs 齒輪模數(蝸桿蝸輪對) |
||
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪(因數COSα/ COSαω數值表) |
||
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪(齒跨距數值表) |
||
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪(齒跨距數值表) |
||
|
CNS 5268
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度(嚙合複合誤差之公差) |
||
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
||
|
CNS 6407
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Yε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算-負載分配因數Yε及齒進度比εβ |
||
|
CNS 6408
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算-齒廓面作用帶因數Z H |
||
|
CNS 6409
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Material Factor Zм 圓柱齒輪與傘齒輪之負載能力計算-材料因數ZM |
||
|
CNS 6410
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算-小齒輪單齒接觸因數ZB,大齒輪單齒接觸因數ZD及正面接觸比εα |
||
|
CNS 6411
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算-接觸比因數Zε |
Find out:10886Items | To Page of: First -Previous-Next -Last | [343] [344] [345] [346] [347] [348] [349] |