"or " CNS Standards List |
|
CNS 10864
1984 Edition Method of Test for Hypo Number of Pulp 紙漿海波值試驗法 |
Translated |
|
|
CNS 4663
1984 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽（片封式，嵌於塑膠製品內） |
|
|
|
CNS 10849
1984 Edition Screw Threads of Valves for High Pressure Gas Cylider 高壓鋼瓶閥螺紋標準 |
Translated |
|
|
CNS 10795
1984 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計（發電機式） |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 1419
1984 Edition Method of Test for Acetone 丙酮檢驗法 |
|
|
|
CNS 5266
1984 Edition Series of Modules for Worm Gear Pairs 齒輪模數（蝸桿蝸輪對） |
|
|
|
CNS 11093
1984 Edition Junction Box for Indoor Wiring (for Polyvinyl-Chloride Insulated and Sheated Cables: VVF) 屋內配線用接線盒[平型聚氯乙烯絕緣聚氯乙烯被覆電纜(VVF)] |
|
|
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 5268
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 11014
1984 Edition Methods of Determination for Manganese in Iron and Steel 鋼鐵中錳定量法 |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 5280
1984 Edition Helix Angles for Cylindrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 11158
1984 Edition Tungsten-Carbide Bits and Rod for Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 11157
1984 Edition Lubrication Holes, Grooves and Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 4731
1984 Edition Knurled Nuts for Drawing Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5298
1984 Edition Hose Clamps for the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 6415
1984 Edition Series of modules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 6414
1984 Edition Basic Rack of Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 6412
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 6411
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 2388
1984 Edition Method of Test for Combustion Rate of Cigarette Paper 捲菸紙燃燒率試驗法 |
Translated |
|
|
CNS 6410
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
| Find out:10886Items | To Page of: First -Previous-Next -Last | [343] [344] [345] [346] [347] [348] [349] |
