"4 " CNS Standards List |
|
CNS 154
2020 Edition Large Unfinished Washers (for Metric Bolts and Nuts: M6 - M52) 粗製大墊圈（用於公制螺栓及螺帽Ｍ６至Ｍ５２） |
Translated |
|
|
CNS 15284
2020 Edition Rims for truck and bus 卡車及大客車用輪圈 |
|
|
|
CNS 5394
2020 Edition Hooks 吊鉤 |
|
|
|
CNS 7114
2020 Edition Cast Steel Flanged Gate Valves (20 kgf/㎠) (Outside Screw Type) 鑄鋼凸緣型閘閥（20 kgf/㎠）（閥桿上升型） |
Translated |
|
|
CNS 3542
2020 Edition Forged shackles for general lifting purposes – Dee shackles and bow shackles 一般起重吊掛用鍛造鉤環－D形鉤環及弓形鉤環 |
|
|
|
CNS 9445-1
2020 Edition Sampling procedures for inspection by variables − Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL 計量值檢驗抽樣程序－第1部：單一品質特性與單一允收品質界限(AQL)逐批檢驗依AQL檢索之單次抽樣計畫 |
|
|
|
CNS 1864
2020 Edition Phosphorus Pentachloride 化學試藥（五氯化磷） |
|
|
|
CNS 8411-2
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Abrasive jet test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－第２部：噴射磨耗試驗法 |
|
|
|
CNS 4157
2020 Edition Metallic and other inorganic coatings – Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium 金屬及其他無機電鍍層－鎳、鎳鉻、銅鎳及銅鎳鉻電鍍層 |
|
|
|
CNS 15443
2020 Edition Sea water mineral concentrate 海水濃縮礦物質液 |
|
|
|
CNS 14964-6
2020 Edition Wheelchairs − Part 6: Determination of maximum speed of electrically powered wheelchairs 輪椅－第6部：電動輪椅最大速率之測定 |
|
|
|
CNS 14276
2020 Edition Electric toys − Safety 電驅動玩具安全要求 |
|
|
|
CNS 62498-3
2020 Edition Railway applications − Environmental conditions for equipment − Part 3: Equipment for signalling and telecommunications 鐵路應用－設備之環境條件－第3部：號誌及電訊設備 |
|
|
|
CNS 5814
2020 Edition Rubber compounding ingredients − Carbon black − Determination of loss on heating 橡膠配合劑－碳黑－加熱減量(熱失量)之測定 |
|
|
|
CNS 14145
2020 Edition Methods of test for measuring thermal expansion of fine ceramics by thermomechanical analysis 精密陶瓷以熱工分析之熱膨脹測定法 |
|
|
|
CNS 2456-5
2020 Edition Plastics piping systems for water supply and for drainage and sewerage under pressure − Polyethylene (PE) − Part 3: Fittings 壓力下給水、排水及排污用塑膠配管系統－聚乙烯(PE)－第5部：系統適合度 |
|
|
|
CNS 496
2020 Edition ISO Metric Screw Threads-Basic Profile (General Purpose) 公制螺紋基準輪廓（ＩＳＯ制） |
Translated |
|
|
CNS 14596
2020 Edition Welding consumables − Gas shielded and self-shielded flux cored wires for arc welding of mild steel, high strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用 鋼氣遮護及自遮護電弧銲接用包藥銲線 |
|
|
|
CNS 14104-1
2020 Edition Prosthetics and orthotics - Classification and description of prosthetic components - Part 3: Description of upper-limb prosthetic components 義肢學與矯具學－肢體缺陷－第１部：先天性肢體缺陷之描述 |
|
|
|
CNS 470
2020 Edition Testing Standard for Cement Roof Tiles 水泥瓦檢驗標準 |
Translated |
|
|
CNS 9074
2020 Edition Retaining rings-C type Ｃ型扣環 |
|
|
|
CNS 14784
2020 Edition Method of test for trace benzene in hydrocarbon solvents by capillary gas chromatography 石油溶劑微量苯試驗法（毛細管柱氣相層析法） |
|
|
|
CNS 4372
2020 Edition Round Thread with Clearance and Steep Flank with Pitch 7mm (Limits of Sizes and Deviations--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙，深螺腹，螺距７ｍｍ之螺紋限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 14626
2020 Edition Cast manganese steel crossings for switch and crossing work 錳鋼岔心 |
|
|
|
CNS 2432
2020 Edition Corn (Zea mays) 玉米 |
|
|
|
CNS 532
2020 Edition Limits of Size and Tolerances for ISO Metric Coarse Screw Threads (Tolerance Quality:Fine,Tolerances:4H、5H and 4h)(Diameters from 1 to 68 mm and Pitches 0.25 to 6 mm) 公制粗螺紋限界尺寸及公差（ISO制）（細品級–4H、5H、4h）（標稱直徑1至68mm，螺距0.25至6mm） |
|
|
|
CNS 15423-1
2020 Edition Equipment for water supply service – Part 1: Test methods of hydrostatic pressure 自來水用器具－第1部：耐壓試驗法 |
|
|
|
CNS 14666
2020 Edition Method of test for vapor pressure of petroleum products (mini method) 石油產品蒸氣壓試驗法（迷你法） |
|
|
|
CNS 4446
2020 Edition Method of test for determination of water in petroleum products, lubricating oils, and additives by coulometric Karl Fisher titration 石油產品水含量測定法（Ｋａｒｌ Ｆｉｓｃｈｅｒ庫侖法） |
|
|
|
CNS 4370
2020 Edition Round Thread with Clearance and Flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
| Find out:6238Items | To Page of: First -Previous-Next -Last | [30] [31] [32] [33] [34] [35] [36] |
