"N,N " CNS Standards List| Low Voltage | Method Test | Electric Dental | Rubber, vulcanized | Method sampling | Non destructive | Travelling Cables | Dynamic host | |
|
CNS 62841-3-1
2017 Edition Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 3-1: Particular requirements for transportable table saws 手持型、可移置型電動工具及草坪與園藝用機械－安全性－第3-1部：可移置型桌鋸之個別規定 |
|
|
|
CNS 4939
2017 Edition Tar epoxy resin paint 環氧樹脂柏油漆 |
|
|
|
CNS 11625
2017 Edition Paper Dielectric Capacitors for AC and DC By-Pass Radio-Interference Reduction 交直流分路射頻干擾衰減用紙介質電容器 |
|
|
|
CNS 11299-6
2017 Edition Glossary of terms for sensing and transducing (Terms of display and record for general instrument technology) 感測與轉換詞彙（有關一般儀表技術之顯示與紀錄名詞） |
|
|
|
CNS 11299-3
2017 Edition Glossary of terms for sensing and transducing (Terms of fundamental concept of trransducing for general instrument technology) 感測與轉換詞彙（有關一般儀表技術之轉換基本觀念名詞） |
|
|
|
CNS 11582
2017 Edition Method of Test for Epoxy ResiN Non-Zinc Primer 環氧樹脂非鋅底漆檢驗法 |
|
|
|
CNS 513
2017 Edition Metric Trapezoidal Screw Threads Allowance and Tolerances for General Purpose Trapezoidal Screw Threads 梯形螺紋（一般用梯形螺紋的裕度及公差） |
|
|
|
CNS 5523
2017 Edition Soft Magnetic Iron Plates 電磁軟鐵板 |
|
|
|
CNS 11589
2017 Edition Method of Test for Oleoresinous Antifouling Paint for Steel Ship Bottom 鋼船用油性船底防污漆檢驗法 |
|
|
|
CNS 11290
2017 Edition Method of Test for Starch in Paper 紙中澱粉含量試驗法 |
Translated |
|
|
CNS 9109
2017 Edition Symbols of Wiring of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖配線類符號 |
|
|
|
CNS 8194
2017 Edition Subplate Type Solenoid Operated 4 - Port Valves for Oil - Hydraulic Use 液壓用副板型四通電磁操作閥 |
|
|
|
CNS 1110
2017 Edition Method of Test for Hand Saws for Carpenter 木工用手鋸檢驗法 |
|
|
|
CNS 502
2017 Edition ISO Metric Fine Screw Threads (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5（ISO制）（標稱直徑12至80公釐，螺距1.5公釐） |
|
|
|
CNS 7087
2017 Edition Dental Pincettes 牙科用鑷子 |
|
|
|
CNS 7379
2017 Edition Carbon Steel Tubes for Boiler and Heat Exchanger 鍋爐及熱交換器用碳鋼鋼管 |
|
|
|
CNS 12495
2017 Edition Laboratory Beating of Pulp (Beater Method) 實驗室紙漿叩解法（打漿機法） |
Translated |
|
|
CNS 5489
2017 Edition Rubber Hinges of Sewing Machines for Industrial use 工業用縫紉機橡皮合葉 |
|
|
|
CNS 10700
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Vibration, Shock and Power Supply Voltage Range) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（振動、衝擊穩定性及電源電壓範圍） |
|
|
|
CNS 5292
2017 Edition Needle Bars of Sewing Machines for Home Use 家庭用縫紉機針棒 |
Translated |
|
|
CNS 6777
2017 Edition Indoor Post Insulators 屋內柱形絕緣體 |
|
|
|
CNS 11646
2017 Edition Glassfiber reinforced plastic pipe for sewer and industrial use 污水與工業用玻璃纖維強化塑膠管 |
|
|
|
CNS 4745
2017 Edition Copper rod drawing stock for electrical purposes 電氣用抽製銅條 |
|
|
|
CNS 4754
2017 Edition Bore Gages (Cylinder Gages) 內徑規（缸徑規） |
|
|
|
CNS 5995
2017 Edition Master Dies for Die Casting Metal Mold 壓鑄模用主模板 |
|
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 15551-1
2017 Edition Ergonomics - Accessible design - Auditory signals for consumer products 人因工程－無障礙設計 - 消費產品之聲音訊號 |
|
|
|
CNS 13991
2017 Edition Fixed resistor networks with individually measurable resistors for use in electronic equipment 電子設備用可單獨量測個別電阻元件之固定網路電阻器 |
|
|
|
CNS 14451
2017 Edition Limestone dimension stone 石灰石石材 |
|
|
|
CNS 4487
2017 Edition Method of test for surface discontinuities –Bolts, screws and studs for general requirements 螺釘表面瑕疵檢驗法 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [363] [364] [365] [366] [367] [368] [369] |
