"co " CNS Standards List| Induction Heating | Magnesium Nitrate | Arm Shafts | Polyvinyl chloride | Nitrogen Gas, | Leather | Glossary terms | Basic Dimensions | |
|
CNS 14500
2019 Edition Vehicles, boats and internal combustion engines − Radio disturbance characteristics − Limits and methods of measurement for the protection of on-board receivers 車輛、船舶及內燃機引擎-無線電擾動特性-保護車載接收機之限制值與量測法 |
||
|
CNS 1169
2019 Edition Method of Test for Resistance of concrete Specimens to Rapid Freezing in Air and Rapid Thawing in Water 混凝土試體抵抗凍融試驗法(空氣中快速冰凍水中快速溶解法) |
||
|
CNS 12514-8
2019 Edition Fire-resistance tests – Elements of building construction – Part 8: Specific requirements for non-loadbearing vertical separating elements 建築物構造構件耐火試驗法-第8 部: 非承重垂直區劃構件特定要求 |
||
|
CNS 8252
2019 Edition Method of cornering Test of Carburetors for Automobiles 汽車用化油器轉彎性能試驗法 |
||
|
CNS 15171
2019 Edition Method of test for flat particles, elongated particles, or flat and elongated particles contents in coarse aggregate 粗粒料中扁平、細長或扁長顆粒含量試驗法 |
||
|
CNS 7779-4
2019 Edition Industrial fans – Determination of fan sound power levels under standardized laboratory conditions – Part 4: Sound intensity method 工業用風機-在標準化實驗室條件下風機聲功率位準測定- 第4部:聲強度法 |
||
|
CNS 12299
2019 Edition Method of Test for Exhaust Smoke Under Noload and Acceleration conditions for Motorcycles 機器腳踏車無負載急加速排煙試驗法 |
||
|
CNS 8465-2
2019 Edition Acoustics - Rating of sound insulation in buildings and of building elements - Impact sound insulation 聲學-建築物及建築構件之隔音量評定-衝擊音隔音 |
||
|
CNS 15200-9-2
2019 Edition Methods of test for paints – Part 9-2: coating powders – Inclined-plane flow test 塗料一般試驗法-第9-2 部:粉體塗料-斜面流動性試驗 |
||
|
CNS 11451
2019 Edition Iron and steel-Methods for determination of niobium content 鐵及鋼─鈮定量法 |
||
|
CNS 13959
2019 Edition Method of test for compressive strength of fine ceramics 精密陶瓷壓縮強度試驗法 |
||
|
CNS 1467
2019 Edition Recording and Computing Methods for Labor Injury 工作傷害記錄及計算方法 |
||
|
CNS 16107-4
2019 Edition Hollow taper interface with flange contact surface − Part 4: Dimensions of receivers for stationary tools 具凸緣接觸面之空心錐度界面-第4部:固定式刀具用接收器之尺度 |
||
|
CNS 16107-3
2019 Edition Hollow taper interface with flange contact surface − Part 3: Dimensions of shanks for stationary tools 具凸緣接觸面之空心錐度界面-第3部:固定式刀具之刀柄尺度 |
||
|
CNS 15593-21
2019 Edition Electricity metering − Data exchange for meter reading, tariff and load control − Part 21: Direct local data exchange 電力計量-讀表、計費及負載控制之資料交換-第21 部:直接本地資料交換 |
||
|
CNS 14934-5
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 5: Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16A 電磁相容-限制值-第5部:額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
||
|
CNS 14374
2019 Edition Method of test for cigarettes -Determination of total and nicotine - free dry particulate matter 捲菸檢驗法-總粒狀物及不含尼古丁乾粒狀物之測定 |
||
|
CNS 15659-1
2019 Edition Evaluation of moisture-absorbing and quick-drying properties in textiles Part 1: combination test 紡織品吸濕速乾性能評估-第1 部:組合試驗法 |
||
|
CNS 15112
2019 Edition Method of test for determination of olefin content of gasolines by supercritical-fluid chromatography 汽油烯烴含量測定法(超臨界流體層析法) |
||
|
CNS 7530
2019 Edition Method of test for grain size of coated abrasive macrogrits (P12-P220) 砂紙、砂布用粗粒磨料粒度試驗法 |
||
|
CNS 1234
2019 Edition Method of Test for Flexural Strength of concrete (Using Simple Beam with Center-point Loading) 混凝土抗彎強度試驗法(中心點載重法) |
Translated |
|
|
CNS 15753
2019 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PP) − Part 7: Guidance for the assessment of conformity 地下排水及排污非壓力塑膠配管系統-聚乙烯(PE) |
||
|
CNS 12217
2019 Edition Method of Test for Facial cotton 化粧棉檢驗法 |
||
|
CNS 15087
2019 Edition Method of test for determination of ethanol content of denatured fuel ethanol by gas chromatography 變性燃料乙醇中乙醇含量測定法(氣相層析法) |
||
|
CNS 8315
2019 Edition Oilseeds - Determination of Moisture and Volatile Matter content 油籽–水分及揮發物質含量之測定 |
Translated |
|
|
CNS 4269
2019 Edition Hot-rolled atmospheric corrosion resisting steels for welded structure 銲接結構用耐候性熱軋鋼料 |
||
|
CNS 14816-1
2019 Edition Low-voltage switchgear and controlgear − Part 1: General rules 低電壓開關裝置及控制裝置-第1部:通則 |
||
|
CNS 3275
2019 Edition Method of Test for Polymethylacrylate corrugated Sheet (Light Penetration) 聚甲基丙烯酸甲酯樹脂波形板檢驗法(光線透過率測定法) |
Translated |
|
|
CNS 15077-2
2019 Edition Test conditions for machining centres - Part 2 : Geometric tests for machines with vertical spindle or universal heads with vertical primary rotary axis (vertical Z-axis) 切削中心機之檢驗條件-第2部:具垂直主軸或萬向頭具垂直向主旋轉軸機器之幾何檢驗(垂直Z軸) |
||
|
CNS 8148
2019 Edition Textiles − Care labelling code using symbols 紡織品洗標 |
Find out:4836Items | To Page of: First -Previous-Next -Last | [39] [40] [41] [42] [43] [44] [45] |