"N,N " CNS Standards List| Light Exposure | Method Test | Letter Symbols | Grease Guns | Information technology | Method analysis | Glossary Terms | Method Test | |
|
CNS 15922
2021 Edition Plastics piping and ducting systems − Plastics pipes and fittings − Method for exposure to direct (natural) weathering 塑膠管及管路系統－熱塑性塑膠管－環柔度測定 |
|
|
|
CNS 11474
2021 Edition Electric Citrus Juicer 電動榨汁機 |
Translated |
|
|
CNS 13965
2021 Edition Method of test for compressive strength of sprayed fire-resistive materials applied to steel structure 鋼骨構造用噴附式防火被覆材料抗壓強度試驗法 |
|
|
|
CNS 10920
2021 Edition V Belts and Pulleys for Electric Motors 電動機用三角橡膠帶及皮帶輪 |
|
|
|
CNS 7405
2021 Edition Method of Test for Density of Paint, Varnish, Lacquer and Related Products 油漆、凡立水、噴漆及有關產品密度測定法 |
|
|
|
CNS 8497
2021 Edition Hot-rolled stainless steel plates, sheets and strips 熱軋不銹鋼鋼板、鋼片及鋼帶 |
|
|
|
CNS 329
2021 Edition Wooden Handle for File 銼刀把 |
|
|
|
CNS 3054
2021 Edition Safflower meal (for feeding) 紅花子粕（飼料用） |
|
|
|
CNS 852
2021 Edition Ductile Cast Iron Special Castings for Pressure Main Lines,All Flanged Tees (AFT) 壓力管路用延性鑄鐵管件–凸緣三通管（ＡＦＴ） |
|
|
|
CNS 1305
2021 Edition Honey 蜂蜜 |
|
|
|
CNS 15289
2021 Edition Determination of the aromaticity of oil in vulcanized rubber compounds 硫化橡膠製品中加工油之多環芳烴含量測定法 |
|
|
|
CNS 5533
2021 Edition Symbols for Sequential Control (Functions) 功能順序控制符號 |
|
|
|
CNS 4470
2021 Edition Castle Nuts, Thin Type 堡形螺帽（低形） |
|
|
|
CNS 5529
2021 Edition Symbols for Sequential Control (Resistors) 電阻器順序控制符號 |
|
|
|
CNS 10880-3
2021 Edition Method of Test for Paint Components - Solvent Insoluble Matter 塗料成分檢驗法–溶劑不溶物 |
|
|
|
CNS 7747
2021 Edition Method of test for water soluble chlorides in pulp, paper and board (Potentiometric method) 紙漿、紙及紙板水溶性氯化物試驗法(電位滴定分析法) |
|
|
|
CNS 7844
2021 Edition Electric and manual pencil sharpeners 電動及手動削鉛筆機 |
|
|
|
CNS 14680
2021 Edition Method of test for Carbadox, Nitrofurazone and Furazolidone in feeds 飼料中卡巴得、硝基呋喃及富來頓檢驗方法 |
|
|
|
CNS 14905-4
2021 Edition Hand-held motor-operated electric tools - Safety - Part 2-4: Particular requirements for sanders and polishers other than disk type 手持型電動工具－安全性－第２－４部：砂光機與拋光機之個別規定（盤式除外） |
|
|
|
CNS 10880-26
2021 Edition Method of Test for Paint Components-Quantitative Test of Total Zinc in Solvent Insolubles 塗料成分檢驗法–溶劑不溶物中總鋅之定量試驗 |
|
|
|
CNS 5705
2021 Edition Vane Motors for Hydraulic Use - Diameter 20 - 50 mm 液壓用輪葉馬達–口徑２０～５０ｍｍ |
|
|
|
CNS 15419-2
2021 Edition Foldaway beds - Safety requirements and tests - Part 2: Test methods 折疊床－安全要求及試驗法－第2部：試驗法 |
|
|
|
CNS 15442
2021 Edition Writing and marking instruments − Specification for caps to reduce the risk of asphyxiation 書寫及標記文具－降低帽蓋窒息風險之規範 |
|
|
|
CNS 13162
2021 Edition Guide for the proposal of CNS national standards 國家標準建議書格式指引 |
|
|
|
CNS 15287
2021 Edition Method of test for hydraulic activity of ground slag by reaction with alkali 水淬高爐爐碴粉與鹼反應之水硬活性試驗法 |
|
|
|
CNS 15424-2
2021 Edition Electric motorcycles battery system – Part 2: The safety requirements of stationary battery system 電動機車電池系統－第2部：固定式電池系統安全要求 |
|
|
|
CNS 4202
2021 Edition Edible Chlorella 食用綠藻 |
Translated |
|
|
CNS 10880-2
2021 Edition Method of Test for Paint Components - Heating Loss 塗料成分檢驗法–加熱減量 |
|
|
|
CNS 793
2021 Edition Basic Dimensions of 40 kgf/㎠ Steel Pipe Flanges 鋼製管凸緣基準尺度（40 kgf/㎠） |
|
|
|
CNS 15853-2
2021 Edition Footwear − Critical substances potentially present in footwear and footwear components – Part 2: Determination of phthalates in footwear materials 鞋類－鞋類及組件之有害物質－第2 部：鞋材中鄰苯二甲酸酯類測定法 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [45] [46] [47] [48] [49] [50] [51] |
