"N,N " CNS Standards List| Self Cutting | Side Milling | Wrench, Socket | Long Roller | Electric motor | B ISDN | Manipulating industrial | Sausage | |
|
CNS 6630
2021 Edition Fountain pens and nibs 鋼筆及筆尖 |
![]() |
|
|
CNS 15628-2
2021 Edition Wheelchair seating − Part 2: Determination of physical and mechanical characteristics of seat cushions intended to manage tissue integrity 輪椅乘坐系統-第2部:維持組織完整性座墊之物理與機械特性的測定 |
![]() |
|
|
CNS 13388-0
2021 Edition Iron and steel − ICP atomic emission spectrometric method – Part 0: General rules 鐵及鋼-感應耦合電漿發光光譜分析法-第0 部:通則 |
![]() |
|
|
CNS 15807
2021 Edition Intelligent transport systems − Communications access for land mobiles (CALM) − Architecture 智慧型運輸系統-陸地行動通訊接取(CALM)-架構 |
![]() |
|
|
CNS 6550
2021 Edition Locate Rings of Molds for Plastics 塑膠型模用定位環 |
![]() |
|
|
CNS 15700-2
2021 Edition Plugs, socket-outlets, vehicle connectors and vehicle inlets − Conductive charging of electric vehicles − Part 1: General requirements 電源端插頭、電源端插座、車輛端插頭及車輛端插座-電動車輛傳導式充電-第2部:針對交流刃片及導電嘴配件之尺度相容性及互換性要求+補充增修1 |
![]() |
|
|
CNS 5265
2021 Edition Method of test for sieve analysis of mineral filler for bituminous paving mixtures 瀝青鋪面混合料用礦物填縫料篩分析試驗法 |
![]() |
|
|
CNS 15733-9-2
2021 Edition CommunicatioN Networks and systems for power utility automation − Part 9-2: Specific communication service mapping (SCSM) − Sampled values over ISO/IEC 8802-3 電力公用事業自動化之通訊網路及系統-第9-2 部:特定通訊服務對映-經由乙太網路之取樣值 |
![]() |
|
|
CNS 6479
2021 Edition Rigid PVC Extrusion Sheet for Duct 風管用硬質聚氯乙烯塑膠平板 |
![]() Translated |
|
|
CNS 15628-3
2021 Edition Wheelchair seating − Part 3: Determination of static, impact and repetitive load strengths for postural support devices 輪椅乘坐系統-第3部:姿勢支撐裝置的靜態、衝擊及反覆負載強度之測定 |
![]() |
|
|
CNS 11325
2021 Edition Reinforced concrete cable troughs 鋼筋混凝土製電纜槽 |
![]() |
|
|
CNS 7355
2021 Edition Method of Test for Round Aluminium Wire for Electrical Wire, Solid 圓鋁單電線檢驗法 |
![]() |
|
|
CNS 9998
2021 Edition Hot-dip aluminium-coated steel sheet and strip 熱浸鍍鋁鋼片及鋼帶 |
![]() |
|
|
CNS 9219
2021 Edition Countersunk Head Grooved Pins 槽銷(埋頭) |
![]() |
|
|
CNS 9810
2021 Edition Rotary Switches for Resistance Welding Machines 電阻電焊機用旋轉開關 |
![]() |
|
|
CNS 9690
2021 Edition Heat-Shrinkable Chloroprene Tubing for Electrical Insulation (Tubular Type) 電絕緣用熱收縮聚氯丁二烯橡膠套管(管狀) |
![]() |
|
|
CNS 9973
2021 Edition Water Gages for Boilers-with Cocks Tubular Type 鍋爐水位計–附10 kgf/㎠旋塞圓管型 |
![]() |
|
|
CNS 5706
2021 Edition Method of Test of Vane Motors for Hydraulic Use - Diameter 20 - 50 mm 液壓用輪葉馬達檢驗法–口徑20~50mm |
![]() |
|
|
CNS 15529
2021 Edition Methods of environmental and endurance test on light emitting diode components 發光二極體元件之環境及 耐久性試驗法 |
![]() |
|
|
CNS 12648
2021 Edition Nylon Hoor and Loop Fastener 尼龍鈎環型黏扣帶 |
![]() |
|
|
CNS 1470
2021 Edition Kerosene 煤油 |
![]() |
|
|
CNS 5196
2021 Edition Neon Glow Lamp 霓虹指示燈泡 |
![]() |
|
|
CNS 6425
2021 Edition Slotting Drills with Morse Taper Shank 開槽銑刀(莫氏圓錐柄) |
![]() |
|
|
CNS 6731
2021 Edition Method of Test for Motorcycle Padlocks Laminate Type 疊片式機車掛鎖檢驗法 |
![]() |
|
|
CNS 14779
2021 Edition Method of test for the particle cylindrical crushing strength of lightweight coarse aggregates 輕質粗粒料之顆粒筒壓強度試驗法 |
![]() |
|
|
CNS 61377
2021 Edition Railway applications − Rolling stock − Combined test method for traction systems 鐵路應用-鐵路車輛-牽引系統綜合試驗法 |
![]() |
|
|
CNS 15533-2
2021 Edition Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries 二次電池及電池安裝之安全性要求-第2部:定置型電池 |
![]() |
|
|
CNS 13802-5
2021 Edition Graphical Symbols for Diagrams (Semiconductors and Electron Tubes) 電機工程製圖符號(半導體及電子管) |
![]() |
|
|
CNS 6793
2021 Edition Low-Voltage Pin Type Insulators 低壓裝腳絕緣器 |
![]() |
|
|
CNS 15152
2021 Edition Disposable pad for adult 成人紙尿片 |
![]() |
Find out:16181Items | To Page of: First -Previous-Next -Last | [66] [67] [68] [69] [70] [71] [72] |