"In " CNS Standards List |
|
CNS 15232
2020 Edition Oils of lemon and petitgraIn citronnier, and oil of lime obtained by a mechanical process - Determination of citral (neral + geranial) content (Gas chromatographic method on capillary columns) 機械程序製檸檬油、檸檬葉油及萊姆油－檸檬油醛（橙花醛＋香葉草醛）含量測定法（毛細管柱氣相層析法） |
|
|
|
CNS 7557
2020 Edition Slip-on WeldIng Steel Pipe Flanges (30 kgf/㎠) 滑入熔接式鋼製管凸緣（30 kgf/㎠） |
|
|
|
CNS 5978
2020 Edition Symbols, DenomInations and Units for Gears Calculation 齒輪計算用參數之符號、名稱及單位 |
|
|
|
CNS 5793
2020 Edition SealIng Caps for Automobiles 汽車用封閉帽塞 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoplastic − DetermInation of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 11191
2020 Edition Method for CalculatIng Heat Balancing of Pottery and Refractory Firing Tunnel Kiln 陶瓷器、耐火物等燒成用隧道窯熱平衡計算方法 |
|
|
|
CNS 5391
2020 Edition Glossary of Terms for MachIne Tools 工具機名詞 |
|
|
|
CNS 519
2020 Edition Limit of Whitworth Threads (FIne Fit) 韋氏螺紋限界尺寸（精配） |
|
|
|
CNS 390
2020 Edition Insert Type Drill Bushing (Metric System) 定鑽襯（公制） |
|
|
|
CNS 11142
2020 Edition Magnesia GrInding Whees 氧化鎂黏結研磨輪 |
Translated |
|
|
CNS 60335-2-2
2020 Edition Household and similar electrical appliances − Safety − Part 2-2: Particular requirements for vacuum cleaners and water-suction cleanIng appliances 家用和類似用途電器－安全性－第2-2部：真空吸塵器及吸水清潔機之個別規定 |
|
|
|
CNS 498
2020 Edition ISO Metric FIne Screw Threads (General) 公制細螺紋１（ＩＳＯ制）（總則） |
Translated |
|
|
CNS 5790
2020 Edition Hazard WarnIng Signal Flashers for Automobiles 汽車用危險警示信號燈閃光器 |
Translated |
|
|
CNS 7558
2020 Edition WeldIng-Neck Steel Pipe Flanges (30 kgf/㎠) 熔接頸鋼製管凸緣（30 kgf/㎠） |
|
|
|
CNS 7565
2020 Edition FormIng End of Rivet Setting 鉚釘工具組（鉚釘頭模） |
|
|
|
CNS 7577
2020 Edition Dimension Over PIns of Spur Gears in the 0.5 System ０．５齒制正齒輪之雙銷直徑尺度 |
|
|
|
CNS 4235
2020 Edition Fasteners－Acceptance Inspection 結件之允收檢驗 |
|
|
|
CNS 4240
2020 Edition Electroplated CoatIng of Bolts, Screws and Nuts 螺栓、螺釘、螺帽之電鍍層 |
|
|
|
CNS 781
2020 Edition OleoresInous Antifouling Paint for Steel Ship Bottom 鋼船用油性船底防污漆 |
Translated |
|
|
CNS 7720
2020 Edition AlumInum Acetate, Basic 化學試藥（鹼式醋酸鋁） |
|
|
|
CNS 9804
2020 Edition Brass Screwed SwIng Check Valves (8.5 kgf/㎠) 黃銅螺紋口擺動型止回閥（8.5 kgf/㎠） |
Translated |
|
|
CNS 7703
2020 Edition Leather - Physical and mechanical tests - DetermInation of water vapour absorption 皮革－物性及機械性質測試－吸濕度試驗法 |
|
|
|
CNS 499
2020 Edition ISO Metric FIne Screw Threads (Diameters From 1 to 3.5mm and Pitches 0.2 to 0.35mm) 公制細螺紋2（ISO制）（標稱直徑1至3.5公釐，螺距0.2至0.35公釐） |
Translated |
|
|
CNS 3126
2020 Edition Bolts, Screws and Studs-NomInal Lengths, and Thread Lengths 螺栓、螺釘、螺樁之長度及螺紋長度 |
|
|
|
CNS 3333
2020 Edition ZInc alloy ingots intended for castings 鑄造用鋅合金錠 |
|
|
|
CNS 1960
2020 Edition Sodium CobaltInitrite 化學試藥（亞硝酸鈷鈉） |
|
|
|
CNS 11908
2020 Edition Plastic BobbIns for Ring Spinning Flame 低壓電表用塑膠箱體及固定板 |
|
|
|
CNS 9745
2020 Edition Method of Test for Calcium Sulfate In Hydrated Portland Cement Mortar 水硬性卜特蘭水泥墁料中硫酸鈣含量之檢驗法 |
|
|
|
CNS 62040-3
2020 Edition UnInterruptible power systems (UPS) − Part 3: Method of specifying the performance and test requirements 不斷電系統(UPS)－第3 部：性能規定法及試驗要求 |
|
|
|
CNS 1995
2020 Edition Stannic Chloride, Anhydrous (FumIng Stannic Chloride, Tin Tetrachloride) 化學試藥（無水氯化錫）（發煙氯化錫，四氯化錫） |
|
| Find out:10338Items | To Page of: First -Previous-Next -Last | [71] [72] [73] [74] [75] [76] [77] |
