"Plastics pipes" CNS Standards List |
|
CNS 15852-3
2022 Edition ThermoPlastics pipes, fittings and assemblies for the conveyance of fluids − Determination of the resistance to internal pressure − Part 3: Preparation of components 流體輸送用熱塑性塑膠管、管件及組合件－耐內壓力測定－第3部：組件製備 |
|
|
|
CNS 15852-4
2022 Edition ThermoPlastics pipes, fittings and assemblies for the conveyance of fluids − Determination of the resistance to internal pressure − Part 4: Preparation of assemblies 流體輸送用熱塑性塑膠管、管件及組合件－耐內壓力測定－第4部：組合件製備 |
|
|
|
CNS 15914
2021 Edition ThermoPlastics pipes for the conveyance of fluids − Determination of resistance to rapid crack propagation (RCP) − Small-scale steady-state test (S4 test) 流體輸送用熱塑性塑膠管－耐快速裂痕擴展(RCP)之測定－小型穩態(S4)試驗 |
|
|
|
CNS 15915
2021 Edition ThermoPlastics pipes for the conveyance of fluids − Determination of resistance to rapid crack propagation (RCP) − Full-scale test (FST) 流體輸送用熱塑性塑膠管－耐快速裂痕擴展(RCP)之測定－全尺度試驗(FST) |
|
|
|
CNS 15858
2021 Edition Plastics pipes and fittings − Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting 塑膠管及管路系統－塑膠管及管件－直接耐候曝露法 |
|
|
|
CNS 15920
2021 Edition Plastics pipes and fittings − Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm 塑膠管及管件－聚乙烯(PE)管/管或管/管件熱熔對接之組合試件製備 |
|
|
|
CNS 15921
2021 Edition ThermoPlastics pipes − Longitudinal reversion − Test method and parameters 熱塑性塑膠管－縱向復原率－試驗法與參數 |
|
|
|
CNS 15918-1
2021 Edition ThermoPlastics pipes − Determination of tensile properties − Part 1: General test method 熱塑性塑膠管－抗拉性能測定第1 部：一般試驗法 |
|
|
|
CNS 15852-2
2021 Edition ThermoPlastics pipes, fittings and assemblies for the conveyance of fluids − Determination of the resistance to internal pressure − Part 2: Preparation of pipe test pieces 流體輸送用熱塑性塑膠管、管件及組合件－耐 內壓力測定－第2 部：管試件製備 |
|
|
|
CNS 15918-3
2021 Edition ThermoPlastics pipes − Determination of tensile properties − Part 3: Polyolefin pipes 熱塑性塑膠管－抗拉性能測定－第3 部：聚烯烴管 |
|
|
|
CNS 15849
2021 Edition Plastics piping and ducting systems − ThermoPlastics pipes − Determination of ring flexibility 塑膠管系統－聚乙烯管材料及組件－揮發物含量測定法 |
|
|
|
CNS 15922
2021 Edition Plastics piping and ducting systems − Plastics pipes and fittings − Method for exposure to direct (natural) weathering 塑膠管及管路系統－熱塑性塑膠管－環柔度測定 |
|
|
|
CNS 15852-1
2021 Edition ThermoPlastics pipes, fittings and assemblies for the conveyance of fluids − Determination of the resistance to internal pressure − Part 1: General method 流體輸送用熱塑性塑膠管、管件及組合件－耐內壓力測定－第1 部：一般方法 |
|
|
|
CNS 15923
2021 Edition ThermoPlastics pipes − Determination of ring stiffness 熱塑性塑膠管－環剛度測定 |
|
|
|
CNS 15860
2021 Edition Plastics pipes and fittings − Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion 塑膠管及管件－聚乙烯(PE)管及電熔接管件組裝試件之製備 |
|
|
|
CNS 2456-3
2020 Edition Plastics piping systems for water supply and for drainage and sewerage under pressure − Polyethylene (PE) − Part 2: Pipes 壓力下給水、排水及排污用塑膠配管系統－聚乙烯(PE)－第3部：管件 |
|
|
|
CNS 12835-3
2020 Edition Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) − Part 2: Pipes 燃氣用塑膠配管系統－聚乙烯(PE)－第3部：管件 |
|
|
|
CNS 7046-3
2018 Edition Plastics piping systems for hot and cold water installations − Polybutene (PB) − Part 2: Pipes 冷熱水裝置用塑膠管配管系統－聚丁烯(PB)－第3部：管件 |
|
|
|
CNS 15609-2
2018 Edition ThermoPlastics pipes and fittings − Vicat softening temperature − Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly(vinyl chloride) (PV 熱塑性塑膠管與管件－衛氏軟化溫度－第2部：未塑化或氯化聚氯乙烯管與管件及高耐衝擊聚氯乙烯管之試驗條件 |
|
|
|
CNS 15609-1
2018 Edition ThermoPlastics pipes and fittings − Vicat softening temperature − Part 1: General test method 熱塑性塑膠管與管件－衛氏軟化 溫度－第1部：一般試驗法 , |
|
|
|
CNS 15609-3
2018 Edition ThermoPlastics pipes and fittings − Vicat softening temperature − Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings 熱塑性塑膠管與管件－衛氏軟化溫度－第3部：丙烯腈-丁二烯-苯乙烯及丙烯腈-苯乙烯-丙烯酸酯管與管件之試驗條件 |
|
|
|
CNS 16016-3
2017 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PP) − Part 2: Pipes 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第3部：管件 |
|
| Find out:22Items | To Page of: First -Previous-Next -Last | 1 |
