"gear " CNS Standards List |
|
CNS 60947-6-1
2023 Edition Low-voltage switchgear and controlgear − Part 6-1: Multiple function equipment − Transfer switching equipment 低電壓開關裝置及控制裝置－第6-1部：多功能設備－轉換開關設備 |
|
|
|
CNS 7575
2022 Edition Tip Diameter of Spur gears in the 0.5 System ０．５齒制正齒輪之齒頂圓直徑 |
|
|
|
CNS 5986
2022 Edition Calculation of Load Capacity for Cylindrical and Bevel gears - Tooth form Factor Yϝ 圓柱齒輪與傘齒輪之負載能力計算–齒形因數Yϝ |
|
|
|
CNS 5985
2022 Edition Calculation of Load Capacity on Tooth Flank for Bevel gears 傘齒輪齒廓面負載能力之計算 |
|
|
|
CNS 5984
2022 Edition Calculation of Load Capacity on Tooth Root for Bevel gears 傘齒輪齒根負載能力之計算 |
|
|
|
CNS 5982
2022 Edition Calculation of Load Capacity on Tooth Root for Cylindrical gears 圓柱齒輪齒根負載能力之計算 |
|
|
|
CNS 5981
2022 Edition The Basic Formulas for gears Calculation 齒輪計算之基本公式 |
|
|
|
CNS 5980
2022 Edition Load Capacity for gears 齒輪之負載能力 |
|
|
|
CNS 7572
2022 Edition Basic Rack Tooth Profile of gear Tools for Cylindrical Gears with Involute Teeth for Fine Mechanics 漸開線圓柱齒輪切齒刀具之基準齒條齒廓（精細機械用） |
|
|
|
CNS 7574
2022 Edition Root Diameter of Spur gears in the 0.5 System ０．５齒制正齒輪之齒底圓直徑 |
|
|
|
CNS 7186
2022 Edition Addendum Modification of Cylindrical gears 圓柱齒輪之齒廓移位 |
|
|
|
CNS 7577
2022 Edition Dimension Over Pins of Spur gears in the 0.5 System ０．５齒制正齒輪之雙銷直徑尺度 |
|
|
|
CNS 7578
2022 Edition Normal Chordal Tooth Thickness and Chordal Height of Spur gears in the 0.5 System ０．５齒制正齒輪之弦齒厚及弦齒冠 |
|
|
|
CNS 7579
2022 Edition Contact Ratio of Spur gears in the 0.5 System ０．５齒制正齒輪之接觸比 |
|
|
|
CNS 7580
2022 Edition Sliding Speed at Tooth Tip of Spur gears in the 0.5 System ０．５齒制正齒輪之齒頂接觸處滑動速率 |
|
|
|
CNS 12378
2022 Edition Method of test for load-carrying capacity for lubricating oil (FZG gear machine method) 潤滑油負載能力試驗法(FZG法) |
|
|
|
CNS 15156-200
2022 Edition High-voltage switchgear and controlgear − Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV 高電壓開關裝置及控制裝置－第200部：額定電壓高於1 kV且在52 kV以下之交流金屬閉鎖型開關裝置及控制裝置 |
|
|
|
CNS 15176-4
2022 Edition Wind turbines − Part 4: Design requirements for wind turbine gearboxes 風力機－第4部：風力機齒輪箱之設計及規範 |
|
|
|
CNS 7573
2022 Edition Centre Distances and Working Transverse Pressures Angles of Spur gears in the 0.5 System ０．５齒制正齒輪之軸中心距及正面工作壓力角 |
|
|
|
CNS 15783-1
2021 Edition Low-voltage switchgear and controlgear assemblies – Part 1: General rules 低電壓開關裝置及控制裝置組裝品－第1部：一般規則 |
|
|
|
CNS 13802-7
2021 Edition Graphical Symbols for Diagrams (Switchgear,Controlgear and Protective Devices) 電機工程製圖符號（開關設備、控制設備及保護設備） |
|
|
|
CNS 15467-2-8
2021 Edition Lamp controlgear - Part 2-8: Particular requirements for ballasts for fluorescent lamps 光源控制裝置－第2-8部：螢光燈管用安定器之個別規定 |
|
|
|
CNS 5701
2021 Edition gear Pumps for Hydraulic Use - Discharge Diameter 10 - 50 mm 液壓用齒輪泵–排出口徑１０～５０ｍｍ |
|
|
|
CNS 15156-203
2021 Edition High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV 高電壓開關裝置及控制裝置－第２０３部：額定電壓超過５２ｋＶ之氣體絕緣金屬封閉型開關裝置 |
|
|
|
CNS 4380
2021 Edition Clearances and Creepage Distances for Control gear 控制機構的絕緣距離 |
|
|
|
CNS 6418
2021 Edition Pinion-type Cutters for Cylindrical gears; Extended Hub Gear Cutters for Spur Gears 圓柱齒輪用齒輪形切齒刀（直齒內齒輪用有柄切齒刀） |
|
|
|
CNS 6416
2021 Edition Pinion-type Cutters for Cylindrical gears; Disc-gear Cutters for Spur Gears 圓柱齒輪用齒輪形切齒刀（正齒輪用鐘形切齒刀） |
|
|
|
CNS 14816-5-5
2021 Edition Low-voltage switchgear and controlgear − Part 5-5: Control circuit devices and switching elements − Electrical emergency stop device with mechanical latching function 低電壓開關裝置及控制裝置－第5-5 部：控制電路裝置及開關操作元件－具機械閂鎖功能之電氣緊急停止裝置 |
|
|
|
CNS 6417
2021 Edition Pinion-Type Cutters for Cylindrical gear; Tolerances 圓柱齒輪用齒輪形切齒刀（正齒輪用圓盤形切齒刀） |
|
|
|
CNS 14816-5-1
2021 Edition Low-voltage switchgear and controlgear − Part 5-1: Control circuit devices and switching elements − Electromechanical control circuit devices 低電壓開關裝置及控制裝置－第5-1 部：控制電路裝置及開關操作元件－電機控制電路裝置 |
|
| Find out:145Items | To Page of: First -Previous-Next -Last | 1 2 3 4 5 |
