"per " CNS Standards List |
|
CNS 15789
2020 Edition Robots and robotic devices – Safety requirements for personal care robots 機器人及機器人裝置－人員照護機器人之安全要求 |
|
|
|
CNS 8279
2020 Edition Dimensions, mass and permissible variations of hot rolled steel bars and bar in coil 熱軋棒鋼及捲狀棒鋼之形狀、尺度、質量及其許可差 |
|
|
|
CNS 12639
2020 Edition Disposable diaper for baby 嬰兒紙尿褲 |
|
|
|
CNS 4157
2020 Edition Metallic and other inorganic coatings – Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium 金屬及其他無機電鍍層－鎳、鎳鉻、銅鎳及銅鎳鉻電鍍層 |
|
|
|
CNS 4372
2020 Edition Round Thread with Clearance and Steep Flank with Pitch 7mm (Limits of Sizes and Deviations--Tolerances and permissible Wear of Thread Gauges) 圓螺紋（具有間隙，深螺腹，螺距７ｍｍ之螺紋限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 15200-6-1
2020 Edition Methods of test for paints - Part 6-1: Chemical property of film - Resistance to liquids 塗料一般試驗法－第6-1部：塗膜化學性質－耐液體性 |
|
|
|
CNS 14601
2020 Edition Welding consumables − Solid wires for MAG and MIG welding of mild steel, high strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用鋼MAG及MIG銲接用實心銲線 |
|
|
|
CNS 15378-2
2020 Edition Fine ceramics - Test method for self-cleaning performance of photocatalytic materials - Part 2: Decomposition of wet methylene blue 精密陶瓷—光觸媒材料之自我潔淨性能測定法—第２部：濕式亞甲基藍分解性能 |
|
|
|
CNS 15173
2020 Edition Ducted air-conditioners and air-to-air heat pumps - Testing and rating for performance 接風管型空氣調節機及空氣對空氣式熱泵之試驗法及性能等級 |
|
|
|
CNS 29182-7
2020 Edition Information technology − Sensor networks: Sensor Network Reference Architecture (SNRA) − Part 7: Interoperability guidelines 資訊技術－感測器網路：感測器網路參考架構(SNRA)－第7部：互運性指導綱要 |
|
|
|
CNS 10019
2020 Edition Rubber, vulcanized or thermoplastic − Determination of compression stress-strain properties 硫化或熱塑性橡膠壓縮應力－應變性質測定法 |
|
|
|
CNS 2519
2020 Edition Railway Sleeper (for 1067 mm Gauge) 鐵路木枕（軌距1067mm者） |
|
|
|
CNS 14104-1
2020 Edition Prosthetics and orthotics - Classification and description of prosthetic components - Part 3: Description of upper-limb prosthetic components 義肢學與矯具學－肢體缺陷－第１部：先天性肢體缺陷之描述 |
|
|
|
CNS 15566-3
2020 Edition Safety of machinery – Pressure-sensitive protective devices – Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices 機械安全－壓敏保護裝置－第3 部：設計及測試壓敏緩衝器、板、線及類似裝置之一般原則 |
|
|
|
CNS 15193-3
2020 Edition Safety of machinery - permanent means of access to machinery - Part 3: Stairs,stepladders and guard-rail 機械安全－接近機械之永久性方法－第３部：階梯、踏梯及護欄 |
|
|
|
CNS 13719
2020 Edition Welding consumables − Covered electrodes for mild steel, high tensile strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用鋼用被覆銲條 |
|
|
|
CNS 4370
2020 Edition Round Thread with Clearance and Flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 14596
2020 Edition Welding consumables − Gas shielded and self-shielded flux cored wires for arc welding of mild steel, high strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用 鋼氣遮護及自遮護電弧銲接用包藥銲線 |
|
|
|
CNS 157
2020 Edition Square Taper Washers (for I Sections) 方形推拔墊圈（工字鐵用） |
|
|
|
CNS 3586
2020 Edition perlite Heat Insulating Sheet (Block) and Pipe 真珠岩保溫板（磚）及保溫管 |
Translated |
|
|
CNS 5038
2020 Edition Laboratory filter paper and method of test 化學分析用濾紙 |
|
|
|
CNS 15373
2020 Edition Liquefied petroleum gases － Determination of dissolved residues (High-temperature gravimetric method) 液化石油氣－可溶殘餘物測定法（高溫重量法） |
|
|
|
CNS 399
2020 Edition Fastening of Taper Pins and Cotter Pins 定位銷裝配位置（用於圓錐銷及開口銷） |
|
|
|
CNS 62282-3-201
2020 Edition Fuel cell technologies − Part 3-201: Stationary fuel cell power systems − performance test methods for small fuel cell power systems 燃料電池技術－第3-201部：定置型燃料電池發電系統－小型燃料電池發電系統之性能試驗法 |
|
|
|
CNS 15356
2020 Edition Test method for continuity of anodic oxide coatings on aluminium and aluminium alloys - Copper sulphate test 鋁及鋁合金之陽極氧化膜連續性試驗法－硫酸銅試驗法 |
|
|
|
CNS 14315
2020 Edition Methods of test for bending fatigue of fine ceramics at room temperature 精密陶瓷室溫彎曲疲勞試驗法 |
|
|
|
CNS 4670-21
2020 Edition Specified Items for Machine Tools - Gear Shapers (Rack Cutter Type) 工具機規範之項目–齒輪刨製機（齒條刨刀型） |
|
|
|
CNS 618
2020 Edition Method of Test for permanent Linear Change of Refractory Brick on Reheating 耐火磚再熱線性脹縮率試驗法 |
|
|
|
CNS 15200-5-4
2020 Edition Methods of test for paints – Part 5-4: Mechanical property of film – Scratch hardness (Pencil method) 塗料一般試驗法－第５－４部：塗膜機械性質：刮痕硬度（鉛筆法） |
|
|
|
CNS 15267
2020 Edition Medical devices - Guidance on the selection of standards in support of recognized essential principles of safety and performance of medical devices 醫療器材－醫療器材安全與性能選擇之指導綱要 |
|
| Find out:1774Items | To Page of: First -Previous-Next -Last | [5] [6] [7] [8] [9] [10] [11] |
