" Test " CNS Standards List |
|
CNS 14820
2017 Edition Method of Test for measuring toxic gases generated by solid material flammability － Gas detector tube 固體材料燃燒毒性氣體濃度試驗法－檢測管法 |
|
|
|
CNS 15481-5
2017 Edition Road vehicles - Environmental conditions and Testing for electrical and electronic equipment - Part 5: Chemical loads 道路車輛－電機電子配備環境條件與試驗－第５部： 化學負載 |
|
|
|
CNS 11582
2017 Edition Method of Test for Epoxy Resin Non-Zinc Primer 環氧樹脂非鋅底漆檢驗法 |
|
|
|
CNS 14782
2017 Edition Manipulating industrial robots —Test equipment and metrology methods of operation for robot performance evaluation 工業用機器人性能評估作業之測試儀器與量測方法 |
|
|
|
CNS 14113
2017 Edition Reliability Tests for passive devices (for fiber optical communication) 光纖通信用被動元件之可靠度測試 |
|
|
|
CNS 15832-2-2
2017 Edition Method of Test for coating components − Part 2-2: Component analysis in solvent soluble matter − Softening point (Ring-and-ball method) 塗料成分試驗法－第2-2部：溶劑可溶物中成分分析－軟化點(環與球法) |
|
|
|
CNS 15343
2017 Edition Furniture - Method of Test for strength and durability of storage units 家具－收納單元之強度與 耐久性測定法 |
|
|
|
CNS 12086
2017 Edition Method of Test for Fiber Optic Devices (FOPT-55 Method for Measuring the Coating Geometry of Optical Fibers) 光纖裝置檢驗法（光纖鍍層幾何形狀之測量法ＦＯＴＰ–５５） |
|
|
|
CNS 7167
2017 Edition Method of Test for Hydroxyl Value of Fatty Oils and Acids 脂肪油及脂肪酸羥價測定法 |
|
|
|
CNS 7642
2017 Edition Method of Test for Fiber Optic Devices (Air Leakage Testing of Fiber Optic Component Seals) 光纖裝置檢驗法（光纖組件密封漏氣試驗ＦＯＴＰ–２３） |
|
|
|
CNS 664
2017 Edition Method of Test for Temperature of Transmission Shaft of Water Pumps 水泵傳動軸溫度檢驗法 |
|
|
|
CNS 11571
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-44 Corona Test) 頻率３ＭＨｚ以下電連接器檢驗法（電暈試驗ＴＰ–４４） |
|
|
|
CNS 10230
2017 Edition Test Code for Accuracy of Slicers 單板平切機精度檢驗 |
|
|
|
CNS 12369
2017 Edition Method of Test for Fiber Optic Devices ( FOTP-45 Microscopic Method for Measuring Fiber Geometry) 光纖裝置檢驗法（測量光纖幾何之微觀方法ＦＯＴＰ–４５） |
|
|
|
CNS 13001
2017 Edition Method of Radiographic Testing for Circumferential Butt Welds of Aluminum Pipes and Tubes 鋁管圓周對頭熔接縫之放射線透射試驗法 |
|
|
|
CNS 3633
2017 Edition Basic Environmental Testing Procedures Part 2: Tests, Test N: Change of Temperature 環境試驗法（電氣、電子）–溫度變化試驗 |
|
|
|
CNS 5664
2017 Edition Test Code for Accuracy of Four-side Planers and Moulders 自動四面刨床精度檢驗標準 |
|
|
|
CNS 4301
2017 Edition Test Code for Accuracy of Surface Grinding Machines with Vertical Grinding Wheel Spindle and Rotary Table 旋轉床台型立式平面磨床精度檢驗標準 |
|
|
|
CNS 13163
2017 Edition Method of Soundness Test for Fillet Welds 填角熔接部之無瑕疵試驗法 |
|
|
|
CNS 3623
2017 Edition Basic Environmental Testing Procedures Part 2:Tests,Test Ca:Damp Heat,Steady State 環境試驗法（電氣、電子）–濕熱（穩態）試驗 |
Translated |
|
|
CNS 14114
2017 Edition Lot-control Tests for passive devices (for fiber optical communication) 光纖通信用被動元件之批品質控制測試 |
|
|
|
CNS 15328-3
2017 Edition Information technology - Radio frequency identification device performance Test methods - Part 3: Test methods for tag performance 資訊技術－無線射頻識別裝置效能測試方法－第３部：標籤效能之測試方法 |
|
|
|
CNS 8839
2017 Edition Methods of Test for Refractive Index of Chemical Products 化學製品折射率測定法 |
|
|
|
CNS 5395
2017 Edition Test Code for Performance of Hydraulic Presses 液壓壓床動態檢驗法 |
|
|
|
CNS 14655-2
2017 Edition Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part2: Method for special reverberation Test rooms 聲學─利用聲壓測定噪音源聲功率位準的工程級方法─用於迴響聲場小型、可移動的聲源─第二部：特殊迴響測試室的方法 |
|
|
|
CNS 15077-10
2017 Edition Test conditions for machining centres - Part 10: Evaluation of thermal distortions 切削中心機之檢驗條件－ 第10部：熱變形之評估 |
|
|
|
CNS 13982-5
2017 Edition Methods of Test for bulk down and feather − Part 5: Determination of the moisture content 羽絨羽毛試驗法－第5部：水分含量測定法 |
|
|
|
CNS 10700
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Vibration, Shock and Power Supply Voltage Range) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（振動、衝擊穩定性及電源電壓範圍） |
|
|
|
CNS 6305
2017 Edition Test Code for Accuracy of Feed Carriages of Band Saw Mills 帶鋸機進給溜板精度檢驗標準 |
|
|
|
CNS 8767
2017 Edition Method of Test for Shore Hardness Testing Machines 蕭氏硬度試驗機檢驗法 |
|
| Find out:4507Items | To Page of: First -Previous-Next -Last | [95] [96] [97] [98] [99] [100] [101] |
