"Co " CNS Standards List |
|
CNS 15524-1
2017 Edition Plastics − Compression moulding of test specimens of thermosetting materials 塑膠－灰分測定法－第1部：一般方法 |
|
|
|
CNS 527
2017 Edition Inspection Plug Gauge for Whitworth Thread Ring Gauge (Go End Limit for Fine, Medium and Coarse Fits) 韋氏螺紋樣圈之量柱及損磨量柱（通過端，精配，中配及粗配） |
|
|
|
CNS 10696
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Adjacent Channel, Spurious Response and Intermodulation Immunity) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（鄰波道、混附響應及互調變抗拒力） |
|
|
|
CNS 16014
2017 Edition InterConnection protocol for devices in smart home 智慧家庭之裝置互連協定 |
|
|
|
CNS 7479
2017 Edition Oil Tempered SiliCon Manganese Alloy Steel Wires for Springs 彈簧用油回火矽錳合金鋼鋼線 |
|
|
|
CNS 13982-3
2017 Edition Methods of test for bulk down and feather − Part 3: Composition (content analysis) 羽絨羽毛試驗法－第3部：組成 |
|
|
|
CNS 11244
2017 Edition Iron and steel – Methods for determination of aluminum Content 鐵及鋼－鋁定量法 |
|
|
|
CNS 5268
2017 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 14636
2017 Edition Determination of accuracy and repeatability of positioning of numerically Controlled machine tools 數值控制工具機定位精度暨重現性檢驗通則 |
|
|
|
CNS 15481-3
2017 Edition Road vehicles - Environmental Conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads 道路車輛－電機電子配備環境條件與試驗－第３部：機械負載 |
|
|
|
CNS 14654
2017 Edition ACoustics - Determination of sound power levels of noise sources using sound pressure - Precision methods for reverberation rooms 聲學─利用聲壓測定噪音源聲功率位準─迴響室的精密級方法 |
|
|
|
CNS 8473
2017 Edition Pin Allocations for Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use with Printed Boards 衝頭（打銷用） |
|
|
|
CNS 14866-2
2017 Edition Measurement of water flow in fully charged closed Conduits - Meters for cold potable water and hot water - Part 2: Installation requirements 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第2部：安裝要求 |
|
|
|
CNS 4303
2017 Edition Slotted Countersunk (Flat) Head Tapping Screws 有槽平頂埋頭自攻螺釘 |
|
|
|
CNS 9504
2017 Edition Methods for estimating average grain size of wrought Copper and copper alloys 銅及銅合金展伸材料之晶粒尺度測定法 |
|
|
|
CNS 523
2017 Edition Plug Connection Devices for Explosion-Proof Type Battery Locomotives 韋氏螺紋量柱（通過端限界尺寸、精配、中配及粗配） |
|
|
|
CNS 15207-10
2017 Edition Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 10: Immunity to conducted disturbances in the extended audio frequency range 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第10部：音頻延伸範圍之傳導擾動免疫力 |
|
|
|
CNS 13982-8
2017 Edition Methods of test for bulk down and feather − Part 8: Determination of fill power with steam Conditioning 羽絨羽毛試驗法－第8部：蒸汽處理後蓬鬆度測定法 |
|
|
|
CNS 10227
2017 Edition Test Code for Accuracy of Glue Spreaders 佈膠機精度檢驗 |
|
|
|
CNS 11573
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-50 Sand and Dust Test) 頻率３ＭＨｚ以下電連接器檢驗法（細砂與塵埃試驗ＴＰ–５０） |
|
|
|
CNS 5376-4
2017 Edition Iron ores—Method for determination of Combined water content 鐵礦石—結合水定量法 |
|
|
|
CNS 12081
2017 Edition Method of Test for Fiber Optic Devices (FOPT-13 Visual and Mechanical Inspection of Fibers,Cables,Connectors and Other Fiber Optic Devices) 光纖裝置檢驗法（光纖、光纜、連接器及其他光纖裝置之目視及機械檢查ＦＯＴＰ–１３） |
|
|
|
CNS 5512
2017 Edition Test Code for Accuracy of Numerically Controlled Machine Tools 數值控制工具機精度檢驗通則 |
|
|
|
CNS 4047
2017 Edition Copper beryllium alloy, phosphor bronze and nickel silver rods, bars and wires 鈹銅、磷青銅及鎳銀之棒及線 |
|
|
|
CNS 9234
2017 Edition Method of Test for Dry Reed Switches (Standard Test Coils, Single Insulation 130 ℃ Wire) 乾式簧開關檢驗法（１３０℃單層絕緣線標準試驗線圈） |
|
|
|
CNS 4580
2017 Edition Bolted Connections with Reduced Body; Studs 減徑柄螺栓之結合法（螺樁） |
|
|
|
CNS 14466-18
2017 Edition Audiovisual, video and television equipment and systems - Part18: Connectors for automatic slide projectors withe built-in triacs for audiovisual application 視聽．影像及電視設備與系統-第１８部：視聽應用具內建三端閘流體之自動幻燈片投影機之連接器 |
|
|
|
CNS 4367
2017 Edition Knuckle Threads for Steel Sheet pieces (up to 0.5 mm Thickness and Appropriated Couplings Dimensions Tolerances) 圓螺紋（厚0.5mm以下之鋼皮製品及其 配合螺紋） |
|
|
|
CNS 528
2017 Edition Adjustable Plug Gauge for Whitworth Thread Ring Gauge (For Testing of Go and No Go Ring Gauge, Fine, Medium and Coarse Fits) 韋氏螺紋活動量規（檢驗通過及不通過端樣圈，精配，中配及粗配） |
|
|
|
CNS 15998
2017 Edition Rubber Compounding ingredients − Carbon black − Determination of aggregate size distribution by disc centrifuge photosedimentometry 橡膠配合劑－碳黑－聚集體粒徑分布之測定(圓盤離心沉降光測定法) |
|
| Find out:4836Items | To Page of: First -Previous-Next -Last | [95] [96] [97] [98] [99] [100] [101] |
