"I " CNS Standards List |
|
CNS 7029
2020 Edition Shape, DImensions and Travel Angles of Drawbar Eyes for Full Trailers 全拖車用拖桿環首之形狀、尺度及活動範圍 |
|
|
|
CNS 14144
2020 Edition Methods of test for fracture toughness of fIne ceramics at elevated temperature 精密陶瓷高溫破壞韌性試驗法 |
|
|
|
CNS 11424
2020 Edition Method of Test for SettIng Time of Refractory Mortar 耐火墁料凝結時間試驗法 |
|
|
|
CNS 5079
2020 Edition Gypsum CastIng and Molding Plaster 鑄用及模型用熟石膏 |
|
|
|
CNS 15775
2020 Edition AcoustIcs − Specification of test tracks for measuring noise emitted by road vehicles and their tyres 聲學－供車輛及其輪胎噪音量測用試驗道規格 |
|
|
|
CNS 12969
2020 Edition PorcelaIn Guide 瓷質金斗與骨灰罎 |
|
|
|
CNS 11081
2020 Edition Method for CalculatIng Heat Balancing of Cement Rotary Kiln 水泥工業用窯爐之熱平衡計算方法 |
|
|
|
CNS 8930
2020 Edition SwItchgears, Contact - Spring Washers 加強型彈簧墊圈（電器開關–接觸用） |
|
|
|
CNS 8988
2020 Edition ChemIcal Reagent(Dry Loss Determination) 化學試藥（乾失量測定） |
|
|
|
CNS 5786
2020 Edition ElectrIc Windshield Washers for Automobiles 汽車擋風玻璃電動噴洗器 |
|
|
|
CNS 15227
2020 Edition SIngle-use medical examination gloves - Part 1: Specification for gloves made from rubber latex or rubber solution 單次使用之醫用檢驗手套－第１部：以乳膠或橡膠溶液製成之手套規格 |
|
|
|
CNS 15345-1
2020 Edition Safety of machInery - Reduction of risk to health from hazardous substances emitted by machinery - Part 1: Principles and specification for machinery manufacturers 機械安全－降低由機械釋放有害性物質對健康造成之風險－第１部：對機械製造商之原則及規範 |
|
|
|
CNS 9350
2020 Edition Bushes for PlaIn Bearings with Lubrication Holes and Grooves 滑動軸承軸襯–有潤滑孔及潤滑槽 |
|
|
|
CNS 15804
2020 Edition OIl of cassia, Chinese type − Determination of trans-cinnamaldehyde content − Gas chromatographic method on capillary columns 肉桂油(中國型)－反桂皮醛含量測定法－毛細管柱氣相層析法 |
|
|
|
CNS 9746
2020 Edition Method of Test for PotentIal Expansion of Portland Cement Mortars Exposed to Sulfate 卜特蘭水泥墁料暴露於硫酸盬中之潛在膨脹檢驗法 |
|
|
|
CNS 1870
2020 Edition PIcks, Two Taper Ends 化學試藥（苦味酸） |
|
|
|
CNS 14678
2020 Edition Coaches-wIndows made from glass 客車廂之玻璃窗 |
|
|
|
CNS 121
2020 Edition Collar (UsIng Heavy Duty Set Screws) 頸圈（用螺絲銷、重型） |
|
|
|
CNS 4542
2020 Edition Terms relatIng to the gages for fasteners 結件詞彙（量規） |
|
|
|
CNS 4238
2020 Edition FInishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 4532
2020 Edition Terms RelatIng to the End (Point) of Fasteners 結件端部詞彙 |
|
|
|
CNS 14797
2020 Edition MIneral spirits（hydrocarbon dry cleaning solvent,petroleum spirits,stoddard solvent） 礦物型溶劑 |
|
|
|
CNS 16129-2
2020 Edition RaIlway applications − Welding of railway vehicles and components − Part 2: Quality requirements and certification of welding manufacturer 鐵路應用－鐵路車輛及其零組件之銲接－第2部：銲接製造廠商品質要求及驗證 |
|
|
|
CNS 12843
2020 Edition Chlorosulfonated Polyethylene Rubber Supported Geomembrane for LandfIll 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布 |
Translated |
|
|
CNS 14315
2020 Edition Methods of test for bendIng fatigue of fine ceramics at room temperature 精密陶瓷室溫彎曲疲勞試驗法 |
|
|
|
CNS 13169
2020 Edition Safety Standards for ConstructIon of Veneer Lathes 單板旋切機之構造安全基準 |
|
|
|
CNS 14503-1
2020 Edition EvaluatIon methods for pitting corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第１部：圖示法 |
|
|
|
CNS 2512
2020 Edition DetermInation of paper sizing − Stöckigt method 紙之上膠度試驗法－史托克法 |
|
|
|
CNS 15820-2
2020 Edition ElectrIc motorcycles − Safety specifications − Part 2: Protection against hydrogen hazards for motorcycles fuelled with compressed hydrogen 電動機車－安全規範－第2 部：防止氫氣危害 |
|
|
|
CNS 8408-2
2020 Edition Accelerated test methods for lIght fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
| Find out:15020Items | To Page of: First -Previous-Next -Last | [95] [96] [97] [98] [99] [100] [101] |
