"In " CNS Standards List |
|
CNS 14432-2
2019 Edition DetermInation of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions − Method by analysis of evolved carbon dioxide − Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test 塑膠材料在控制堆肥條件下最終好氧生物分解度測定法－二氧化碳釋出量分析法－第2部：實驗室規模重量測定法 |
|
|
|
CNS 15200-9-1
2019 Edition Methods of test for paInts – Part 9-1: Coating powders – Determination of gel time of thermosetting coating powders at a given temperature 塗料一般試驗法－第9-1 部：粉體塗料－指定溫度下熱固性粉體塗料膠化時間測定 |
|
|
|
CNS 14374
2019 Edition Method of test for cigarettes -DetermInation of total and nicotine - free dry particulate matter 捲菸檢驗法－總粒狀物及不含尼古丁乾粒狀物之測定 |
|
|
|
CNS 11307
2019 Edition Electroplated CoatIngs of Silver for Engineering Use 工程用銀電鍍層 |
|
|
|
CNS 15614
2019 Edition Information technology − Telecommunications and information exchange between systems − Near Field Communication − Interface and Protocol(NFCIP-1) 資訊技術－系統間電信與資訊交換－近場通訊－介面與協定(NFCIP-1) |
|
|
|
CNS 15758-1
2019 Edition PackagIng for terminally sterilized medical devices – Part 1: Requirements for materials, sterile barrier systems and packaging systems 最終滅菌醫療器材之包裝－第1 部：材料、無菌屏障系統及包裝系統之要求 |
|
|
|
CNS 8379
2019 Edition 600 V Grade heat-resistant polyvInyl chloride insulated wires 600 V 耐熱聚氯乙烯絕緣電線(HIV) |
|
|
|
CNS 14004
2019 Edition Environmental management systems − General guidelInes on implementation 環境管理系統－實施之一般指導綱要 |
|
|
|
CNS 15659-2
2019 Edition Evaluation of moisture-absorbIng and quick-drying properties in textiles − Part 2: Moisture management test 紡織品吸濕速乾性能評估－第2 部：水分傳導試驗法 |
|
|
|
CNS 13391
2019 Edition Steel CastIngs - General Technical Requirements 鑄鋼件之製造、試驗及檢驗通則 |
|
|
|
CNS 3086
2019 Edition Method of test for determInation of moisture content in pulp, paper and board（Oven-drying method） 紙漿、紙及紙板含水率測定法（烘箱法） |
|
|
|
CNS 15142
2019 Edition Textiles - DetermInation of fabric propensity to surface fuzzing and to pilling : Modified Martindale method 紡織品起毬檢驗法－改良馬丁代爾法 |
|
|
|
CNS 675
2019 Edition 600 V Rubber Insulated wire 600 V 橡膠絕緣電線 |
|
|
|
CNS 2233
2019 Edition Method of Test for Urea ResIn Adhesives 尿素膠檢驗法 |
Translated |
|
|
CNS 20349-2
2019 Edition Personal protective equipment − Footwear protectIng against risks in foundries and welding − Part 2: Requirements and test methods for protection against risks in welding and allied processes 個人防護具－防止鑄造及熔接中風險之鞋類－第2部：防護熔接及類似製程風險之要求事項及試驗方法 |
|
|
|
CNS 14900
2019 Edition Essential oils - General rules for packagIng, conditioning and storage 精油－包裝材料、調節及儲存通則 |
|
|
|
CNS 60245-7
2019 Edition Rubber Insulated cables − Rated voltages up to and including 450/750 V − Part 7: Heat resistant ethylene-vinyl acetate rubber insulated ables 額定電壓450/750 V 以下橡膠絕緣電纜－ 第7部：耐熱乙烯-醋酸乙烯酯橡膠絕緣電纜 |
|
|
|
CNS 4179
2019 Edition Methods of measurIng case depth of steel hardened by flame or induction hardening process 鋼料火焰淬火及高週波淬火硬化層深度測定法 |
|
|
|
CNS 13306-1-1
2019 Edition Specification for radio disturbance and immunity measurIng apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus 射頻擾動和免疫力量測設備與量測方法－第１－１部：射頻擾動和免疫力量測設備－量測設備 |
|
|
|
CNS 15760-2
2019 Edition Footwear − General test methods – Part 2: SamplIng location, preparation and duration of conditioning of samples and test pieces 鞋類－ 一般試驗法－ 第2 部： 樣品與試片之取樣部位、製備及狀態調節時間 |
|
|
|
CNS 16112
2019 Edition Specification and qualification of weldIng procedures for metallic materials − Qualification by adoption of a standard welding procedure specification 金屬材料銲接程序規範書及其檢定－依〝標準銲接程序規範書〞檢定 |
|
|
|
CNS 13306-1-5
2019 Edition Specification for radio disturbance and immunity measurIng apparatus and methods - Part 1-5: Radio disturbance and immunity measuring apparatus - Antenna calibration test sites for 30 MHz to 1000 MHz 射頻擾動和免疫力量測設備與量測方法－第１－５部：射頻擾動和免疫力量測設備－30 MHz至 1000 MHz之天線校正場地 |
|
|
|
CNS 2770-22
2019 Edition Method of test for feeds - DetermInation of crude fat in extruded feed 飼料檢驗法－熟化飼料粗脂肪之測定 |
Translated |
|
|
CNS 15077-5
2019 Edition Test conditions for machIning centers - Part 5 : Accuracy and repeatability of positioning of work-holding pallets 切削中心機之檢驗條件－第５部：工件夾持托板之定位精度與重現性 |
|
|
|
CNS 14949
2019 Edition Method of test for the determInation of individual components in spark ignition engine fuels by 100 metre capillary (with precolumn) high-resolution gas chromatography 汽油組成分測定法(高解析毛細管柱氣相層析法) |
|
|
|
CNS 15110
2019 Edition Method of test for hydrocarbon types, oxygenated compounds and benzene In spark ignition engine fuels by multi-dimensional gas chromatography 汽油碳氫化合物類型、含氧化物及苯含量測定法（多維管柱系統式氣相層析法） |
|
|
|
CNS 5559
2019 Edition Shape and MountIng Dimensions of Distributor Contact Breakers for Automobiles 汽車用分電盤白金總成之形狀及安裝尺度 |
Translated |
|
|
CNS 16094-1
2019 Edition Ductile iron pipes, fittIngs, accessories and their joints − External zinc-based coating − Part 1: Metallic zinc with finishing layer 延性鑄鐵管、管件、配件及接頭－外部鋅基塗層－第1部：金屬鋅及精整層 |
|
|
|
CNS 3376-7
2019 Edition Explosive atmospheres - Part 7: Equipment protection by Increased safety〝e〞 爆炸性環境－第７部：增加安全構造〝ｅ〞之設備保護 |
|
|
|
CNS 7
2019 Edition Lead Ingot 鉛錠 |
Translated |
| Find out:10338Items | To Page of: First -Previous-Next -Last | [96] [97] [98] [99] [100] [101] [102] |
