"as " CNS Standards List| Method Soundness | Accuracy Inspection | Double End | Method Separation | Assistive products | AC Solenoids | Method Test | Rubber compounding | |
|
CNS 12294
1988 Edition Reliability assured FIxed Carbon Composition Resistors (Form 2,Gradex) 可靠度保證混合碳固定電阻器(方式2之等級X) |
Translated |
|
|
CNS 12209
1988 Edition Sets of High Strength Torque Control Bolt, Hexagon Nut and Plain Washers 控制扭矩之高強度螺栓、六角螺帽及平墊圈組 |
Translated |
|
|
CNS 9145
1988 Edition 660V, Single-Core, Twin-Core, Three-Core Silicon Rubber Insulated Glass Fibber Braided Cable(660V-SSRD, 660V-DSRD, 660V-TSRD) for Marine Use 船用660 V單心、二心、三心矽橡膠絕緣玻璃纖維編織電纜(660 V-SSRD，660 V-DSRD，660 V-TSRD) |
|
|
|
CNS 12210
1988 Edition Method of Test for Sets of High Strength Torque Control Bolt, Hexagon Nut and Plain Washers 控制扭矩之高強度螺栓、六角螺帽及平墊圈組檢驗法 |
|
|
|
CNS 12291
1988 Edition General Rules for Reliability assured Fixed Carbon Composition Resistors 可靠度保證混合碳固定電阻器總則 |
|
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 11898
1987 Edition Reliability assured Plastic Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 12068
1987 Edition Support of Die Casting Molds 壓鑄模用支座 |
|
|
|
CNS 6071
1987 Edition 600 V Silicon Rubber Insulated Glass Fiber Braided Wires 600 V矽橡膠絕緣玻璃纖維編織電線 |
Translated |
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (Quality Control and Quality assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas Flame Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 11937
1987 Edition Runner Pull Pins of Molds for Plastics 塑膠型模用流道拉銷 |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for Plastics 塑膠型模用止銷 |
|
|
|
CNS 8871
1987 Edition Dental Plaster 牙科用普通石膏 |
|
|
|
CNS 10927
1987 Edition Method of Test for Fiber Optic Devices (FOTP-28 Measuring Failure Point of Optical Waveguide Fiber) 光纖裝置檢驗法（光纖抗強拉度測量法FOTP-28） |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 11934
1987 Edition Stop Bolts of Molds for plastics 塑膠型模用止動螺栓 |
|
|
|
CNS 12069
1987 Edition Ejector Rod of Die Casting Molds 壓鑄模用頂出桿 |
|
|
|
CNS 11939
1987 Edition Setting Plugs of Molds for Plastics 塑膠型模用定位塞 |
|
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 11932
1987 Edition Angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 5535
1987 Edition Small Switch for Single-phase Motors 單相電動機用小型開關 |
Translated |
|
|
CNS 11938
1987 Edition Sprue Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 12072
1987 Edition Locating Pin of Die Casting Molds 壓鑄模用定位銷 |
|
|
|
CNS 10926
1987 Edition Method of Test for Fiber Optic Devices (FOTP-27 Measuring Outside (Uncoated) Diameter of Optical Fibers) 光纖裝置檢驗法（無外被光纖外徑測量法FOTP-27） |
|
|
|
CNS 712
1987 Edition Brass Screwed Globe Valves (10 kgf/㎠) 黃銅螺紋口球型閥(10 kgf/cm2) |
Translated |
|
|
CNS 12080
1987 Edition Glossary of Terms Used in Electronic Measuring Apparatus 電子測定器詞彙 |
|
|
|
CNS 12082
1987 Edition Method of Test for Fiber Optic Devices (FOPT-30 Frequency Domain Measurement of Multimode Optical Fiber Information Transmission Capacity) 光纖裝置檢驗法（多模光纖資訊傳輸量之頻域測量FOTP-30） |
|
| Find out:3287Items | To Page of: First -Previous-Next -Last | [99] [100] [101] [102] [103] [104] [105] |
