"C " CNS Standards List |
|
CNS 1048
2020 Edition RefraCtory Mortar 耐火墁料 |
|
|
|
CNS 3-16
2020 Edition Engineering Drawing (GeometriCal Tolerancing - Principles and Methods of Verification) 工程製圖（幾何公差–檢測原理與方法） |
|
|
|
CNS 15212-4
2020 Edition Clinical Thermometers - Part 4: Performance of electrical thermometers for continuous measurement 電子體溫計－第４部：用於連續量測之電子體溫計的性能 |
|
|
|
CNS 10052
2020 Edition Nominal dimensions of veneer lathes 薄片木車床之標稱尺度 |
|
|
|
CNS 5786
2020 Edition EleCtric Windshield Washers for Automobiles 汽車擋風玻璃電動噴洗器 |
|
|
|
CNS 15200-4-1
2020 Edition Methods of test for paints - Part 4-1: Visual Characteristics of film - Hiding power 塗料一般試驗法－第４－１部：塗膜視覺特性－遮蓋力 |
|
|
|
CNS 8215
2020 Edition Steering Bearings for MotorCycles 機車用轉向軸承 |
|
|
|
CNS 1538
2020 Edition Aluminium Potassium Sulfate 12-Water (Reagent) 化學試藥（１２水合硫酸鉀鋁） |
|
|
|
CNS 2012
2020 Edition L(+)-TartariC Acid 化學試藥（Ｌ（＋）–酒石酸） |
|
|
|
CNS 705
2020 Edition Method of Test for VolCanic Ash for General Use 火山灰（一般用）檢驗法 |
|
|
|
CNS 3745
2020 Edition Series 1 freight Containers - Specification for corner fittings 第一類貨櫃－櫃角裝置規格 |
|
|
|
CNS 4238
2020 Edition Finishes and ToleranCes of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 9568
2020 Edition Adapter Sleeves for Rolling Bearings 滾動軸承套接套筒（附螺帽與鎖緊墊圈） |
|
|
|
CNS 9481
2020 Edition Test methods for measuring tire uniformity 輪胎均勻性試驗法 |
|
|
|
CNS 9341
2020 Edition Oil Seals 油封 |
|
|
|
CNS 10023
2020 Edition Plutonium By Controlled - Potential Coulometry 布層心體橡膠輸送帶 |
|
|
|
CNS 1812
2020 Edition MetaphosphoriC Acid 化學試藥（偏磷酸） |
|
|
|
CNS 14293
2020 Edition Pyrogallol PyrogalliC Acid 1,2,3-Trihydroxybenzene 實驗室用參考示溫錐 |
|
|
|
CNS 6502
2020 Edition Method of test for spiCes and condiments – Determination of cold water-soluble extract 香辛料及調味料之檢驗法－冷水萃取物之測定 |
|
|
|
CNS 15802
2020 Edition Essential oils − Determination of water Content − Karl Fischer method 精油－含水量測定法－卡耳費雪法 |
|
|
|
CNS 24508
2020 Edition ErgonomiCs − Accessible design − Guidelines for designing tactile symbols and characters 人因工程學－無障礙設計－觸覺符號與字符之設計指導綱要 |
|
|
|
CNS 15317-3
2020 Edition Crosslinked polyethylene (PE-X) pipe for hot and cold water conveyance - Part 3: Fittings 冷熱水輸送用交連聚乙烯管－第３部：管件 |
|
|
|
CNS 14116
2020 Edition Method of test for traCe quantities of sulfur in light liquid petroieum hydrocarbons by oxidative microcoulometry 輕質液態石油產品中微量硫分試驗法（氧化微庫侖法） |
|
|
|
CNS 1870
2020 Edition PiCks, Two Taper Ends 化學試藥（苦味酸） |
|
|
|
CNS 61439-3
2020 Edition Low-voltage switChgear and controlgear assemblies − Part 3: Distribution boards intended to be operated by ordinary persons (DBO) 低電壓開關裝置及控制裝置組裝品－第3部：由一般人員操作之配電盤(DBO) |
|
|
|
CNS 12455
2020 Edition Methods of tensile test for butt welded joints 對接銲之接頭拉伸試驗法 |
|
|
|
CNS 469
2020 Edition Flat Ridge Type Cement Tiles 平脊形水泥瓦 |
Translated |
|
|
CNS 7922
2020 Edition Method of test for spiCes and condiments – Determination of non-volatile ether extract 香辛料及調味料之檢驗法－非揮發性乙醚萃取物之測定 |
|
|
|
CNS 14503-1
2020 Edition Evaluation methods for pitting Corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第１部：圖示法 |
|
|
|
CNS 15077-9
2020 Edition Test Conditions for machining centres - Part 9 : Evaluation of the operating time of tool change and pallet change 切削中心機之檢驗條件－第９部：刀具與托板更換之操作時間評估 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [101] [102] [103] [104] [105] [106] [107] |
