CNS Standards Solution | HOME | LOGIN | SIGN UP | CONTACT US | 中文版 |
�� ��

Chinese National Standards
中華民國國家標準
- Taiwan 台灣 -
 

"U " CNS Standards List

K-Chemical Industry
CNS 15109    2019 Edition
DenatUred fuel ethanol for blending with gasolines for use as automotive spark-ignition engine fuel
變性燃料乙醇(含生質酒精)-供汽油摻配作為汽車火花點火引擎燃料

Translated
P-Pulp & PaperIndustry
CNS 15288    2019 Edition
Method of test for total coUnt of bacteria, yeast and mould of pulp, paper and board
紙漿、紙及紙板中細菌、酵母菌與黴菌菌落數測定法
C-Electrical Engineering
CNS 15207-7    2019 Edition
Road vehicles - Component test methods for electrical distUrbances from narrowband radiated electromagnetic energy - Part 7: Direct radio frequency (RF) power injection
道路車輛-窄頻輻射電磁能量之電擾動組件試驗法-第7部:直接射頻功率注入
L-Textile Industry
CNS 16113-3    2019 Edition
Textiles − Methods for determination of certain aromatic amines derived from azo colorants − Part 3: Detection of the Use of certain azo colorants, which may release 4-Aminoazobenzene
紡織品-偶氮色料衍生特定芳胺的測定法-第3部:偵測使用之特定偶氮色料可能釋放出的4-胺基偶氮苯
D-Automotive & Aircraft Engineering
CNS 7137    2019 Edition
Sine-vibration testing method for aUtomobile parts
車輛零組件正弦振動試驗法
C-Electrical Engineering
CNS 61215-1-4    2019 Edition
Terrestrial photovoltaic (PV) modUles − Design qualification and type approval − Part 1-4: Special requirements for testing of thin-film Cu(In,Ga)(S,Se)₂ based photovoltaic (PV) modules
陸上太陽光電模組-設計確認和型式認可-第1-4部:(硫、硒)化銅(銦、鎵)薄膜型太陽光電模組特別試驗要求
C-Electrical Engineering
CNS 14816-1    2019 Edition
Low-voltage switchgear and controlgear − Part 1: General rUles
低電壓開關裝置及控制裝置-第1部:通則
K-Chemical Industry
CNS 22    2019 Edition
SUlfuric Acid for Industrial Use
硫酸(工業用)

Translated
C-Electrical Engineering
CNS 8379    2019 Edition
600 V Grade heat-resistant polyvinyl chloride insUlated wires
600 V 耐熱聚氯乙烯絕緣電線(HIV)
C-Electrical Engineering
CNS 11446-2    2019 Edition
Methods of measUrement on receives for television broadcast transmission-Part2: Audio channels-General methods and methods for monophnic channels
電視廣播傳輸接收機之量測方法-第2部 : 聲道-一般方法與單聲道方法
B-Mechanical Engineering
CNS 15077-5    2019 Edition
Test conditions for machining centers - Part 5 : AccUracy and repeatability of positioning of work-holding pallets
切削中心機之檢驗條件-第5部:工件夾持托板之定位精度與重現性
N-Agriculture, Food
CNS 3646    2019 Edition
Method of test for edible oils and fats - Determination of iodine valUe
食用油脂檢驗法-碘價之測定
C-Electrical Engineering
CNS 61347-2-13    2019 Edition
Lamp controlgear − Part 2-13: ParticUlar requirements for d.c. or a.c. supplied electronic controlgear for LED modules
光源控制裝置-第2-13部:LED模組用直流或交流電子式控制裝置之個別要求
B-Mechanical Engineering
CNS 3122    2019 Edition
Hexagon head screws − ProdUct finished and semi-finished
六角頭螺釘-產品等級精製及半精製
Z4-Quality Control
CNS 17065    2019 Edition
Conformity assessment − ReqUirements for bodies certifying products, processes and services
符合性評鑑-產品、過程及服務驗證機構之要求事項
A-Civil Engineering & Architecture
CNS 14842    2019 Edition
Method of test for slUmp flow of high flowing concrete
高流動性混凝土坍流度試驗法
K-Chemical Industry
CNS 15200-9-1    2019 Edition
Methods of test for paints – Part 9-1: Coating powders – Determination of gel time of thermosetting coating powders at a given temperatUre
塗料一般試驗法-第9-1 部:粉體塗料-指定溫度下熱固性粉體塗料膠化時間測定
A-Civil Engineering & Architecture
CNS 15046    2019 Edition
Method of test for measUring the longitudinal profile of traveled surfaces with an accelerometer established inertial profiling reference
慣性剖面儀量測舖面縱向剖面試驗法
K-Chemical Industry
CNS 15053    2019 Edition
Biodiesel - Fatty acid methyl esters (FAME) - Determination of potassiUm content by atomic absorption spectrometry
生質柴油(脂肪酸甲酯)-鉀含量測定法(原子吸收光譜法)
L-Textile Industry
CNS 1494-8    2019 Edition
Textiles-ColoUr fastness to domestic and commercial laundering using a non-phosphate reference detergent incorporating a low temperature bleach activator
紡織品-耐家庭與商用洗滌色牢度試驗法-無磷酸鹽標準清潔劑與低溫漂白活化劑
K-Chemical Industry
CNS 12537    2019 Edition
Poly alUminum chloride for waste water
自來水用聚氯化鋁
F-Ship building Engineering
CNS 7792    2019 Edition
Ships' Chain for General Use
船舶一般用鏈
C-Electrical Engineering
CNS 15207-4    2019 Edition
Road vehicles - Component test methods for electrical distUrbances from narrowband radiated electromagnetic energy - Part 4: Bulk current injection (BCI)
道路車輛-窄頻輻射電磁能量之電擾動組件試驗法-第4部:大電流注入
S-Domestic Wares
CNS 15562-9    2019 Edition
Stationary training eqUipment − Part 9: Elliptical trainers, additional specific safety requirements and test methods
固定式訓練器材-第9部:橢圓訓練機之附加特定安全要求與試驗法
Z7-General & Miscellaneous
CNS 13753    2019 Edition
Corrosion of metals and alloys − Corrosivity of atmospheres − Determination of corrosion rate of standard specimens for the evalUation of corrosivity
金屬及合金之腐蝕-大氣腐蝕性-測定標準試片之腐蝕速率以評估腐蝕性
C-Electrical Engineering
CNS 15120    2019 Edition
Secondary cells and batteries for photovoltaic energy systems (PVES) − General reqUirements and methods of test
太陽光電能源系統用之二次單電池與電池組-一般要求與試驗法
D-Automotive & Aircraft Engineering
CNS 8572    2019 Edition
Glossary of Terms Relating to Electric EqUipment for Automobiles (Charging, Starting, Ignition, Preheating System)
汽車用電器零件詞彙(充電、起動、點火、預熱系統)
K-Chemical Industry
CNS 12628    2019 Edition
Plastics − Unplasticized poly (vinyl chloride) sheets − Part 2: Types, dimensions and characteristics for sheets of thickness less than 1 mm
塑膠及硬橡膠-彈簧式硬度計之凹壓硬度(蕭氏硬度)測定法
Z2-Industry Safety
CNS 15746-2    2019 Edition
Textile slings − Safety − Part 2: RoUndslings, made of man-made fibres for general purpose use
紡織吊帶-安全-第2 部:一般用人造纖維製圓帶
B-Mechanical Engineering
CNS 16107-4    2019 Edition
Hollow taper interface with flange contact sUrface − Part 4: Dimensions of receivers for stationary tools
具凸緣接觸面之空心錐度界面-第4部:固定式刀具用接收器之尺度

Find out:11052Items   |  To Page of: First -Previous-Next -Last  | [101] [102] [103] [104] [105] [106] [107]

 

| HOME | LOGIN | SIGN UP | CONTACT US | 中文版 | ©  CNS-standards.org Copyright  2001-2025 All Rights Reserved
The authority agency link :
Bureau of Standards, Metrology & Inspection M.O.E.A.
This site is not affiliated with or endorsed by the BSMI or MOEA.