"8 " CNS Standards List |
|
CNS 5283
2017 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度（齒廓面元線誤差之公差） |
|
|
|
CNS 4038
2017 Edition Parallel Bench Vices 鉗工虎鉗（圓膛定座式） |
Translated |
|
|
CNS 8473
2017 Edition Pin Allocations for Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use with Printed Boards 衝頭（打銷用） |
|
|
|
CNS 8839
2017 Edition Methods of Test for Refractive Index of Chemical Products 化學製品折射率測定法 |
|
|
|
CNS 12886
2017 Edition Method of Test for Accelerated Aging of Paper and Paperboard - Dry Heat Treatment at 105℃ 紙及紙板加速老化試驗法─105℃乾熱處理 |
Translated |
|
|
CNS 15581
2017 Edition Grading rules for hardwood sawn lumber 闊葉樹製材分等 |
|
|
|
CNS 9803
2017 Edition Welding procedure qualification test for pressure vessels 壓力容器熔接施工方法之確認試驗 |
|
|
|
CNS 4877
2017 Edition Method of Test for Pointer Type Voltmeters 指針型電壓計檢驗法 |
|
|
|
CNS 10683
2017 Edition Round Steel Chains Without Quality Requirements 圓鋼製環鏈（不涉及品質要求） |
|
|
|
CNS 7748
2017 Edition Method of Test for Viscosity of Pulp ( Cannon -Fenske Capillary Viscometer Method ) 紙漿黏度試驗法（Ｃａｎｎｏｎ–Ｆｅｎｓｋｅ毛細管黏度計法） |
Translated |
|
|
CNS 8836
2017 Edition Method of Test for Freezing Point of Chemical Products 化學製品凝固點測定法 |
|
|
|
CNS 11898
2017 Edition Reliability Assured Plastic Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性Ｍ） |
|
|
|
CNS 10378
2017 Edition Method of Test for Folding Endurance of Paper and Paperboard (MIT Tester) 紙及紙板耐折強度試驗法（ＭＩＴ試驗機） |
Translated |
|
|
CNS 12083
2017 Edition Method of Test for Fiber Optic Devices (FOPT-33 Fiber Optic Cable Tensile Loading and Bending Test) 光纖裝置檢驗法（光纜拉力負載與彎曲試驗ＦＯＴＰ–３３） |
|
|
|
CNS 15328
2017 Edition Information technology - Automatic identification and data capture techniques - Radio frequency identification device performance test methods 資訊技術－自動識別與資料擷取技術－無線射頻識別裝置效能測試方法 |
|
|
|
CNS 4589
2017 Edition General Rules of Fixed Capacitors for Use in Electronic Equipment 電子設備用固定電容器通則 |
|
|
|
CNS 13989
2017 Edition Glossary of terms for production automation and inventory management (General) 生產自動化與庫存管理詞彙（一般名詞） |
|
|
|
CNS 3830
2017 Edition High Manganese Steel Castings 高錳鋼鑄鋼件 |
Translated |
|
|
CNS 328
2017 Edition Straight Wrench Lever 直扳柄 |
|
|
|
CNS 168
2017 Edition Tangential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 2958
2017 Edition Cast-iron Pipes and Fittings for Sanitary Equipments 衛生設備用鑄鐵管及管件 |
|
|
|
CNS 248
2017 Edition Insert-teeth Machine Reamer, with Square Head 機用鑲齒鉸刀（方頭圓柱柄） |
|
|
|
CNS 4481
2017 Edition Hexagon Socket Set Screws with Cone End 六角承窩無頭錐形端固定螺釘 |
|
|
|
CNS 10681
2017 Edition Saw Blades for Woodworking Crosscut Saws 木工用橫切鋸鋸片 |
|
|
|
CNS 14866-2
2017 Edition Measurement of water flow in fully charged closed conduits - Meters for cold potable water and hot water - Part 2: Installation requirements 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第2部：安裝要求 |
|
|
|
CNS 12844
2017 Edition Method of Test for Chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布檢驗法 |
Translated |
|
|
CNS 12874
2017 Edition Basic Environmental Testing Procedures Part 2:Tests,Test Kb:Salt Mist,Cyclic(Sodium Chloride Solution) 環境試驗法（電氣、電子）–鹽霧（循環）試驗 |
|
|
|
CNS 8918
2017 Edition Primary Standards ( replaced by CNS 12983 ) 固定式消防用加壓離心泵之原動機 |
|
|
|
CNS 5376-8
2017 Edition Iron ores—Method for determination of manganese content 鐵礦石－錳定量法 |
|
|
|
CNS 5668
2017 Edition Draw - in Bolt End for Milling Machine Arbors 銑刀心軸螺栓端部 |
|
| Find out:4917Items | To Page of: First -Previous-Next -Last | [103] [104] [105] [106] [107] [108] [109] |
