"And " CNS Standards List |
|
CNS 67
2017 Edition Dimensions of Driving Squares And Shanks for Rotating Tools 旋轉刀具之方頭尺度及其柄徑 |
|
|
|
CNS 524
2017 Edition Plug Gauge for Whitworth Thread (Go End Limit for Fine, Medium And Coarse Fits) 韋氏螺紋量柱（不通過端限界尺寸，精配，中配及粗配） |
|
|
|
CNS 13144
2017 Edition Method of Test for Internal Bonding Strength of Paper And Paperboard ( Using Tensile Strength Tester ) 紙及紙板內部結合強度試驗法（使用抗張強度試驗機) |
Translated |
|
|
CNS 14546
2017 Edition LED traffic signal lanterns And lamp housing 發光二極體交通號誌燈燈面及燈箱 |
|
|
|
CNS 15624
2017 Edition Paragliding equipment – Harnesses – Safety requirements And strength tests 飛行傘設備─套袋─安全要求與強度試驗 |
|
|
|
CNS 6834-3
2017 Edition Testing methods for rubber And plastics hoses - Part 3: Determination of resistance to vacuum 橡膠管及塑膠管試驗法－第3部：耐負壓試驗 |
|
|
|
CNS 10695
2017 Edition Method of Test for LAnd Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 13062
2017 Edition Methods of Test for Prepreg of Carbon Fiber And Epoxy Resins 碳纖維及環氧樹脂製預浸材料檢驗法 |
|
|
|
CNS 4421
2017 Edition Seating Bolts And Conical Spring Washers for Clamping 夾緊用座螺栓與錐形彈簧墊圈 |
|
|
|
CNS 14492-1
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part1:General considerations And methods of measurement,including audio-frequency measurements 不同發射類別之無線電接收機的量測方法-第1部:概論及含括音頻量測在內的量測方法 |
|
|
|
CNS 14694-5
2017 Edition Audio , video And audiovisual systems- interconnections and matching values Part 5：Y/C Connector for video systems-Electrical matching values and description of the connector 聲音、影像及視聽系統之互連與匹配值－第５部：影像系統適用之Ｙ／Ｃ連接器－電氣匹配值與連接器說明 |
|
|
|
CNS 14137
2017 Edition Method of eddy current test for titanium pipes And tubes 鈦管渦電流檢測法 |
|
|
|
CNS 1142
2017 Edition Pliers And nippers - Lever assisted side cutting pliers 夾鉗與剪鉗試驗法 |
|
|
|
CNS 3093
2017 Edition Cemented Carbide Dies for Drawing Wires And Rods 超硬合金抽線模 |
|
|
|
CNS 4948
2017 Edition Coupling Screws with Collared Nut And Washers for Double-Ties 具突緣螺帽及墊圈之連接螺釘（雙併枕木用） |
|
|
|
CNS 16016-2
2017 Edition Plastics piping systems for hot And cold water installations − Polypropylene (PP) − Part 1: General 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第2部：管 |
|
|
|
CNS 517
2017 Edition Metric Buttress Screw Thread, Allowance And Tolerance 公制鋸齒形螺紋（裕度及公差） |
|
|
|
CNS 305
2017 Edition HAnd Taps for Whitworth Pipe Threads 絲公，手用，適於韋氏管子螺紋 |
Translated |
|
|
CNS 13127
2017 Edition Metallic And Other Non -organic Coatings -General Rules for Stationary Outdoor Exposure Corrosion Tests 金屬和無機被覆–靜態戶外曝露腐蝕試驗通則 |
|
|
|
CNS 4300
2017 Edition Test Code for Accuracy of Surface Grinding Machines With Horizontal Grinding Wheel Spindle And Reciprocating Table 往復床台型臥式平面磨床精度檢驗標準 |
Translated |
|
|
CNS 12884
2017 Edition Method of sampling And preparing wood for general analysis and preparation of wood for chemical analysis 紙漿用木材取樣與調製法及化學分析用木材之製備法 |
|
|
|
CNS 1021
2017 Edition Picks, One Flat End And One Taper End 十字鎬（一端為尖錐狀，一端為鋼撬狀） |
|
|
|
CNS 4655
2017 Edition Hexagon Set Screws with Half Dog Point And Cone End 六角頭短柱錐形端固定螺釘 |
|
|
|
CNS 11456
2017 Edition Particulate And bulk materials - General rules for methods of sampling 粉塊混合物－取樣法通則 |
|
|
|
CNS 744
2017 Edition Testing StAndard for Rubber Rollers of Rice 碾米 |
Translated |
|
|
CNS 502
2017 Edition ISO Metric Fine Screw Threads (Diameters from 12 to 80mm And Pitch 1.5mm) 公制細螺紋5（ISO制）（標稱直徑12至80公釐，螺距1.5公釐） |
|
|
|
CNS 2831
2017 Edition Fixtures for Aluminium Conducting Wires And Cables 鋁導體電線電纜用配件 |
|
|
|
CNS 13001
2017 Edition Method of Radiographic Testing for Circumferential Butt Welds of Aluminum Pipes And Tubes 鋁管圓周對頭熔接縫之放射線透射試驗法 |
|
|
|
CNS 13064
2017 Edition Methods of Test for Specific Gravity of Epoxy Resins And Hardeners 環氧樹脂及硬化劑比重測定法 |
|
|
|
CNS 4122
2017 Edition Type A1 stAndard test block for ultrasonic testing 超音波檢測用Ａ１型標準規塊 |
|
| Find out:4887Items | To Page of: First -Previous-Next -Last | [104] [105] [106] [107] [108] [109] [110] |
