"et " CNS Standards List |
|
CNS 13618
2018 Edition Method of Test for Potential Alkali-Silica Reactivity of Aggregates(Chemical Method) 粒料之潛在鹼質與二氧化矽反應性試驗法（化學法） |
|
|
|
CNS 16077
2018 Edition Hoists for the transfer of disabled persons − Requirements and test methods 身心障礙者移位用起吊裝置－要求及試驗法 |
|
|
|
CNS 15593-46
2018 Edition Electricity metering − Data exchange for meter reading, tariff and load control – Part 46: Data link layer using HDLC protocol 電力計量－讀表、計費及負載控制之資料交換－第46部：使用HDLC協定之資料鏈路層 |
|
|
|
CNS 13705
2018 Edition Integrated Services Digital Network (ISDN) Connected Line Identification Restriction (COLR) Supplementary Service 整體服務數位網路之連接號碼不顯示增添服務 |
|
|
|
CNS 453
2018 Edition Wood – Determination of compression properties 木材抗壓試驗法 |
|
|
|
CNS 8183
2018 Edition Method of Test for Building Components (Steel Panel for Roof) 建築用組件（鋼製屋頂嵌板）檢驗法 |
|
|
|
CNS 8751
2018 Edition Polyolefin pipes for the conveyance of fluids − Determination of resistance to crack propagation − Test method for slow crack growth on notched pipes 聚烯羥類織袋用帶狀延伸紗 |
|
|
|
CNS 8152
2018 Edition Green coffee − Determination of moisture content 咖啡生豆－水分含量測定法 |
|
|
|
CNS 15620-5
2018 Edition Insulation coordination for equipment within low-voltage system – Part 5: Comprehensive method for determining clearance and creepage distances equal to or less than 2 mm 低電壓系統下設備之絕緣協調－第5 部： 決定2 mm 以下空間距離及沿面距離之詳盡方法 |
|
|
|
CNS 14150
2018 Edition Line transmission of non-telephone signals - System for establishing communication between audiovisual terminals using digital channels up to 2Mbit/s 非電話信號之線傳輸–使用可達２Ｍｂｐｓ數位通道建立視聽終端機間通訊之系統 |
|
|
|
CNS 14865
2018 Edition Packaging-Complete,filled transport packages and unit loads-Horizontal impact tests 包裝貨物與單位裝載之水平衝擊試驗法 |
|
|
|
CNS 6358
2018 Edition Method of test for water and sediment in fuel oils by the centrifuge method 燃料油水分與沈澱物試驗法 (離心法) |
|
|
|
CNS 8076
2018 Edition Building Components (Concrete Panels for Floors) 建築用組件（混凝土樓板嵌板） |
|
|
|
CNS 973
2018 Edition Method of Test for Canned Food-Inspection for Interior of Can 食品罐頭檢驗法–罐內壁檢查 |
Translated |
|
|
CNS 10688
2018 Edition Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange - Functional Description of Interchange Circuit 資料終端設備與資料電路終端設備間互換用串列二進資料之介面–互換電路的功能敘述 |
|
|
|
CNS 18893
2018 Edition Mobile elevating work platforms − Safety principles, inspection, maintenance and operation 移動式升降工作平台−安全原則、檢驗、維護及操作 |
|
|
|
CNS 12365
2018 Edition Alphanumeric Character Sets for Optical Recognition - Part II : Character Set OCR-B-Shapes and Dimensions of the Printed Image 光學辨識用文數字集–第二部，ＯＣＲ–Ｂ字集–印出影像之形狀與尺度 |
|
|
|
CNS 15037-2
2018 Edition Walking aids manipulated by both arms - Requirements and test methods - Part 2: Rollators 雙臂操作步行輔具－要求及測試法－第２部：帶輪助行器 |
|
|
|
CNS 9136
2018 Edition 250V Single-Core, Twin-Core, Three-Core EPR Insulated CP Sheathed Metal Netting Covered Cable (250V-SPNC, 250V-DPNC, 250V-TPNC) and PVC Anti-Corrosion Cable (250V-SPNCY, 250V-DPNCY, 250V-TPNCY) for Marine Use 船用２５０Ｖ單心、二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜及２５０Ｖ單心、二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜 |
|
|
|
CNS 14952-3-1
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials - Part 3: Instructions for calculating thermal endurance characteristics - section 1: calculations using mean values of normally distributed complete data 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第１章：利用常態分配完整資料的平均值進行計算 |
|
|
|
CNS 13733
2018 Edition Broadband Integrated Services Digital Network (B-ISDN) Services Profile 寬頻整體服務數位網路之服務規範 |
|
|
|
CNS 15006
2018 Edition Flow-metering devices for connection to terminal units of medical gas pipeline systems 連接於醫療氣體管線系統終端單元之流量計裝置 |
|
|
|
CNS 16060
2018 Edition Rubber, raw natural − Determination of plasticity retention index (PRI) 天然橡膠生膠－塑性殘留指數測定法 |
|
|
|
CNS 4026
2018 Edition Permissible Deviations in Dimensions Without Tolerance Indication (Metallic Sintered Products) 一般許可差（金屬燒結品） |
|
|
|
CNS 10623
2018 Edition Marine Plugs and Socket-Outlets ( Watertight Type ) 船用插頭及出線插座（防水型） |
|
|
|
CNS 13660-2
2018 Edition File Transfer,Access and Management (FTAM)-Part 2:Definition of Type,Constraint Sets and Syntaxes 檔案轉送、存取及管理–第２部分：文件型式限制集合與語法基本定義 |
|
|
|
CNS 2158
2018 Edition Method of Test fo Dissolved Acetylene (for Industrial Use) 工業用溶解乙炔檢驗法 |
|
|
|
CNS 14637-3
2018 Edition Test code for machine tools − Part 3: Determination of thermal effects 工具機試驗規範－第3部：熱效應之決定 |
|
|
|
CNS 3-14
2018 Edition Engineering Drawing (Geometrical Tolerancing - Datums and Datum - Systems) 工程製圖（幾何公差–基準及基準系統之標註） |
|
|
|
CNS 5341
2018 Edition Determination of density for vulcanized or thermoplastic rubber 硫化橡膠或熱塑性橡膠密度測定法 |
|
| Find out:7275Items | To Page of: First -Previous-Next -Last | [111] [112] [113] [114] [115] [116] [117] |
