"F " CNS Standards List |
|
CNS 8484
2019 Edition Method oF Test for Control Cables for Automobles 汽車用操縱線檢驗法 |
|
|
|
CNS 15754
2019 Edition Plastics piping systems For non-pressure underground drainage and sewerage − Polyethylene (PE) 建築物內污水排放塑膠配管系統－聚乙烯(PE) |
|
|
|
CNS 10209
2019 Edition Gaskets For Windows, Doors and Joints of Panel in Buildings 建築用墊條 |
Translated |
|
|
CNS 14934-5
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 5: Limitation oF voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16A 電磁相容－限制值－第5部：額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
|
|
|
CNS 9011
2019 Edition Rubber hose For oil discharge 輸油用橡膠管 |
|
|
|
CNS 11013
2019 Edition Iron and steel－Methods For determination of silicon content 鐵及鋼－矽定量法 |
|
|
|
CNS 5611
2019 Edition General principles oF physical testing methods for textiles 紡織品物理試驗法通則 |
|
|
|
CNS 12222
2019 Edition Methods oF test for water vapour permeability of textiles 紡織品透濕度試驗法 |
Translated |
|
|
CNS 15716
2019 Edition Oil oF turpentine, Iberian type (Pinus pinaster Sol.) 松節油(伊比利亞型) |
|
|
|
CNS 8579
2019 Edition Glossary oF Terms Relating to Electric Equipment for Automobiles(Wiring Harness) 汽車用電器零件詞彙（配線束） |
|
|
|
CNS 14128
2019 Edition Method oF impact test for instrument panel of passenger cars 小客車用儀表板衝擊試驗法 |
|
|
|
CNS 13275
2019 Edition Method oF test for analysis of natural gas by gas chromatography 天然氣成分試驗法－氣相層析法 |
|
|
|
CNS 16107-3
2019 Edition Hollow taper interFace with flange contact surface − Part 3: Dimensions of shanks for stationary tools 具凸緣接觸面之空心錐度界面－第3部：固定式刀具之刀柄尺度 |
|
|
|
CNS 13753
2019 Edition Corrosion oF metals and alloys − Corrosivity of atmospheres − Determination of corrosion rate of standard specimens for the evaluation of corrosivity 金屬及合金之腐蝕－大氣腐蝕性－測定標準試片之腐蝕速率以評估腐蝕性 |
|
|
|
CNS 15040
2019 Edition Paints and varnishes - Determination oF the volatile organic compound content of low - VOC emulsion paints (in-can VOC) 塗料與清漆－低ＶＯＣ乳膠漆（罐內ＶＯＣ）揮發性有機化合物含量之測定 |
|
|
|
CNS 4827
2019 Edition Electroplated coatings oF zinc on iron and steel 鋼鐵底材之鋅電鍍層 |
|
|
|
CNS 15030-4
2019 Edition ClassiFication and labelling of chemicals − Oxidizing gases 化學品分類及標示－氧化性氣體 |
Translated |
|
|
CNS 15760-1
2019 Edition Footwear – General test methods – Part 1: Standard atmospheres for conditioning and testing of footwear and components for footwear 鞋類－ 一般試驗法－ 第1 部： 鞋類與鞋類部件狀態調節及測試之標準大氣狀態 |
|
|
|
CNS 15030-5
2019 Edition ClassiFication and labelling of chemicals − Gases under pressure 化學品分類及標示－加壓氣體 |
Translated |
|
|
CNS 13301
2019 Edition Method oF inspection for gas pressure welded joint of steel bars for concrete reinforcement 鋼筋混凝土用鋼筋瓦斯壓接接頭檢查法 |
|
|
|
CNS 16107-4
2019 Edition Hollow taper interFace with flange contact surface − Part 4: Dimensions of receivers for stationary tools 具凸緣接觸面之空心錐度界面－第4部：固定式刀具用接收器之尺度 |
|
|
|
CNS 3646
2019 Edition Method oF test for edible oils and fats - Determination of iodine value 食用油脂檢驗法－碘價之測定 |
|
|
|
CNS 16093-1
2019 Edition Welding and allied processes − Types oF joint preparation − Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels 銲接及其相關製程－接頭準備型式－第1部：鋼的被覆銲條電弧銲接、氣體遮護金屬電弧銲接、氣銲、惰氣遮護金屬電弧銲接及能束銲接 |
|
|
|
CNS 15104
2019 Edition Textiles - Determination oF abrasion resistance of fabrics by the Martindale method - Part 2 : Determination of specimen breakdown 紡織品耐摩損性馬丁代爾試驗法－第２部:試樣耐摩損試驗法 |
|
|
|
CNS 16121-2
2019 Edition Electrical apparatus For the detection of combustible gases in domestic premises − Part 2: Electrical apparatus for continuous operation in a fixed installation in recreational vehicles and similar premises − Additional test methods and performance requir 家居處所可燃氣體偵測用之電氣裝備－第2部：固定裝設於休旅車船及類似處所之持續操作用電氣裝備－附加試驗方法及性能要求 |
|
|
|
CNS 5606
2019 Edition Methods oF Test for Strength Properties of Adhesives in Shear by Tension Loading 黏著劑之抗剪強度測定法（拉力負荷法） |
|
|
|
CNS 1009
2019 Edition Methods oF Test for Tea 茶葉檢驗法 |
Translated |
|
|
CNS 13602
2019 Edition General construction oF gas burning appliances for domestic use 家庭用燃氣燃燒器具構造通則 |
|
|
|
CNS 15077-8
2019 Edition Test conditions For machining centers - Part 8 : Evaluation of contouring performance in the three coordinate planes 切削中心機之檢驗條件－第８部：在三個坐標平面內之輪廓性能評估 |
|
|
|
CNS 14632
2019 Edition Finger joined along longitudinal direction of structural lumber used in platform construction 框組壁工法結構用指接縱接材 |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [113] [114] [115] [116] [117] [118] [119] |
