"an " CNS Standards List |
|
CNS 14952-3-1
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials - Part 3: Instructions for calculating thermal endurance characteristics - section 1: calculations using mean values of normally distributed complete data 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第１章：利用常態分配完整資料的平均值進行計算 |
|
|
|
CNS 15590-7
2018 Edition Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 3515
2018 Edition Cycles − Audible warning devices − Technical specification and test methods 自行車－聲音警告裝置－技術規定及測試法 |
|
|
|
CNS 14344
2018 Edition Fittings for weathertight steel doors (Rectangular corner type) 船用鋼質風雨密門（方角型）裝具 |
|
|
|
CNS 15609-1
2018 Edition Thermoplastics pipes and fittings − Vicat softening temperature − Part 1: General test method 熱塑性塑膠管與管件－衛氏軟化 溫度－第1部：一般試驗法 , |
|
|
|
CNS 15569-2
2018 Edition Hydraulic fluid power – Filter elements – Part 2: Verification of fabrication integrity and determination of the first bubble point 液壓流體動力－過濾器濾心－第2部：查證製作完整性及測定首次起泡點 |
|
|
|
CNS 4022
2018 Edition Permissible Deviations in Dimensions Without Tolerance Indication (Die Castings) 一般許可差（壓鑄） |
|
|
|
CNS 11524
2018 Edition Method of test for windows and doors-general rule 門窗性能試驗法通則 |
|
|
|
CNS 14227
2018 Edition Formats and codes of the ISDN user part of signalling system No.7 第七號信號系統–整體服務數位網路使用者部格式及編碼 |
|
|
|
CNS 6391
2018 Edition Method of test for meat and meat products - Determination of nitrate content 肉及肉製品檢驗法－硝酸鹽含量之測定 |
|
|
|
CNS 14151
2018 Edition Line transmission of non-telephone signals - Procedures for establishing communication between threeor more audiovisual terminals using digital channels up to 2Mbit/s 非電話信號之線傳輸–使用可達２Ｍｂｐｓ數位通道建立三部或以上視聽終端機間通訊之程序 |
|
|
|
CNS 60335-2-15
2018 Edition Household and similar electrical appliances − Safety − Part 2-15: Particular requirements for appliances for heating liquids 家用和類似用途電器－安全性－第2-15部：加熱液體用電器之個別規定 |
|
|
|
CNS 9152
2018 Edition 660V, Single-core, Twin-core, Three-core, EPR Insulated CP Sheathed Metal Netting Covered Cable and 660V Single-Core,Three-Core EPR Insulated CP Sheathed Metal Netting Covered PVC Anti-corrosion Cable for Marine Use 船用６６０Ｖ單心、二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜（附共同遮蔽）及６６０Ｖ單心、二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附共同遮蔽） |
|
|
|
CNS 10855
2018 Edition Criteria for Selection of Plastics Used for Marine Electrical Appliances 船用電器塑膠選用準則 |
|
|
|
CNS 1910
2018 Edition Pylon Slalom Test Procedure for Passenger Car and Light Trailer Combination 吡啶（試藥） |
|
|
|
CNS 10239
2018 Edition Data Processing Vocabulary (Part 10: Operating Techniques and Facilities) 資料處理詞彙（第１０部：作業技術及裝備） |
|
|
|
CNS 13515
2018 Edition Standard Sand 標準砂 |
|
|
|
CNS 14431
2018 Edition Method of test for performance of oil/grease interceptor 油脂截留器性能試驗法 |
|
|
|
CNS 61347-1
2018 Edition Lamp controlgear − Part 1: General and safety requirements 光源控制裝置－第1部：通則及安全要求 |
|
|
|
CNS 11010
2018 Edition Electric storage tank water heaters 貯備型電熱水器 |
Translated |
|
|
CNS 13940-2
2018 Edition Identification cards - Optical memory cards - Linear recording method; Part 2: Dimensions and location of the accessible optical area 識別卡–光學記憶卡–線性記錄法；第２部：可存取光學區的尺寸與位置 |
|
|
|
CNS 4394-2
2018 Edition Plastics − Injection moulding of test specimens of thermoplastic materials − Part 1: General principles, and moulding of multipurpose and bar test specimens 塑膠－熱塑性塑膠射出成型試片－第2部：小型拉伸試驗棒 |
|
|
|
CNS 9154
2018 Edition 660V, Twin-Core, Thre-Core EPR Insulated CP Sheathed Metal Netting Covered Cable and 660V Twin-Core, Three-Core EPR Insulated CP Sheathed Metal Netting Cover PVC Anti-Corrosion Cable for Marine Use 船用６６０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜（附各心線個別遮蔽）及６６０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附各心線個別遮蔽） |
|
|
|
CNS 9274
2018 Edition Hot-rolled steel plate, sheet and strip for automobile structural uses 汽車結構用熱軋鋼板、鋼片及鋼帶 |
|
|
|
CNS 13714
2018 Edition Functional Description of the Message Transfer Part (MTP) Level 3 of Signalling System No.7 第七號信號系統訊息轉送部第３階功能描述 |
|
|
|
CNS 14393-8
2018 Edition Biological evaluation of medical devices - Part 8: Selection and qualification of reference materials for biological tests 醫療器材生物性評估－第８部：生物測試用參考材料之選擇及資格認定 |
|
|
|
CNS 13853-2
2018 Edition Information technology - Computer graphics - Metafile for the storage and transfer of picture description information - Part 2:Character encoding 資訊技術–電腦圖形–儲存與轉送圖象描述資訊的元檔–第２部：字元編碼 |
|
|
|
CNS 15568
2018 Edition Protecting Equipment and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 12050
2018 Edition Heat resistant glass wares 耐熱玻璃製食品器具 |
|
|
|
CNS 7354
2018 Edition Hard Drawn Aluminium Stranded Conductors 硬鋁絞電線 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [113] [114] [115] [116] [117] [118] [119] |
