"LA " CNS Standards List |
|
CNS 8791
1988 Edition Method of Test for Low-Temperature Characteristics of Heat Shrinkable Tubing for Electrical InsuLAtion 電絕緣用熱收縮套管低溫特性試驗法 |
|
|
|
CNS 12210
1988 Edition Method of Test for Sets of High Strength Torque Control Bolt, Hexagon Nut and PLAin Washers 控制扭矩之高強度螺栓、六角螺帽及平墊圈組檢驗法 |
|
|
|
CNS 12241
1988 Edition Steel PLAtes, Sheets for Layered Pressure Vessels 多層卷壓力容器用高張力鋼板及鋼帶 |
Translated |
|
|
CNS 12248
1988 Edition Methods of Test for Pressure-sensitive Adhesive Tapes for Electrical InsuLAtion 電絕緣用黏帶試驗法 |
|
|
|
CNS 8784
1988 Edition Method of Test for Tensile of Heat Shrinkable Tubing for Electrical InsuLAtion 電絕緣用熱收縮套管拉伸試驗法 |
|
|
|
CNS 12254
1988 Edition Quartz Crystal Units for OscilLAtors (for 200-1000 kHz) 振盪器用石英振盪晶體(200 MHz～1000 MHz用) |
|
|
|
CNS 12253
1988 Edition Quartz Crystal Units For OscilLAtors (For 1 MHz -- 125 MHz) 振盪器用石英振盪晶體(1 MHz～125 MHz用) |
|
|
|
CNS 8785
1988 Edition Method of Test for Electric Strength of Heat Shrinkable Tubing for Electrical InsuLAtion 電絕緣用熱收縮套管絕緣強度試驗法 |
|
|
|
CNS 12209
1988 Edition Sets of High Strength Torque Control Bolt, Hexagon Nut and PLAin Washers 控制扭矩之高強度螺栓、六角螺帽及平墊圈組 |
Translated |
|
|
CNS 6064
1987 Edition InsuLAted Wire for Neon Tube 氖氣管用絕緣電線 |
Translated |
|
|
CNS 12085
1987 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler LAunch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求FOTP-54） |
|
|
|
CNS 12074
1987 Edition FLAsh Cavity of Hot Forging Closed Die 熱鍛閉合模之餘料穴 |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas FLAme Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-LAunch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 11939
1987 Edition Setting Plugs of Molds for PLAstics 塑膠型模用定位塞 |
|
|
|
CNS 11938
1987 Edition Sprue Puller of Molds for PLAstics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 11937
1987 Edition Runner Pull Pins of Molds for PLAstics 塑膠型模用流道拉銷 |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for PLAstics 塑膠型模用止銷 |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for PLAstics 塑膠型模用支持座 |
|
|
|
CNS 6071
1987 Edition 600 V Silicon Rubber InsuLAted Glass Fiber Braided Wires 600 V矽橡膠絕緣玻璃纖維編織電線 |
Translated |
|
|
CNS 9101
1987 Edition Graphical Symbols of Interior Wiring Diagram for Architectural PLAns 屋內配線設計圖符號總則 |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for PLAstics 塑膠型模用頂出套筒 |
|
|
|
CNS 12122
1987 Edition Method of Test on Communication Receivers for Amplitude-ModuLAtion Transmissions 調幅通信接收機檢驗法 |
|
|
|
CNS 1369
1987 Edition Weather-proof P. E. InsuLAted Wires 塑膠（聚乙烯）風雨電線 |
Translated |
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for PLAstics 塑膠型模用頂出導銷 |
|
|
|
CNS 3070
1987 Edition InsuLAting Oil (for Cold Area) 絕緣油（寒地用） |
Translated |
|
|
CNS 2728
1987 Edition Aluminium Stranded Wires for InsuLAted Cables 絕緣電纜用鋁絞線 |
Translated |
|
|
CNS 11932
1987 Edition Angle Pins of Molds for PLAstics 塑膠型模用角銷 |
|
|
|
CNS 2662
1987 Edition Electric PercoLAtors 電咖啡壺 |
Translated |
|
|
CNS 11934
1987 Edition Stop Bolts of Molds for pLAstics 塑膠型模用止動螺栓 |
|
| Find out:3991Items | To Page of: First -Previous-Next -Last | [119] [120] [121] [122] [123] [124] [125] |
