"D C " CNS Standards List |
|
CNS 56
2019 Edition Methods of test for soaps 肥皂試驗法 |
|
|
|
CNS 14545-4
2019 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 0:Glow-wire test methods-General 火災危險性試驗－第２部：試驗方法－第１章／第０單元：熾熱線試驗方法－通則 |
|
|
|
CNS 964
2019 Edition Dentistry – Manual toothbrushes – General requirements and test methods 牙科－手動牙刷－一般要求及試驗法 |
|
|
|
CNS 7269
2019 Edition Polypropylene band 聚丙烯繩索 |
Translated |
|
|
CNS 15077-8
2019 Edition Test conditions for machining centers - Part 8 : Evaluation of contouring performance in the three coordinate planes 切削中心機之檢驗條件－第８部：在三個坐標平面內之輪廓性能評估 |
|
|
|
CNS 4827
2019 Edition ElectroplateD Coatings of zinc on iron and steel 鋼鐵底材之鋅電鍍層 |
|
|
|
CNS 1494-8
2019 Edition Textiles-Colour fastness to domestic anD Commercial laundering using a non-phosphate reference detergent incorporating a low temperature bleach activator 紡織品－耐家庭與商用洗滌色牢度試驗法－無磷酸鹽標準清潔劑與低溫漂白活化劑 |
|
|
|
CNS 12223
2019 Edition Granulated (Water quenched) blast furnace slag 水淬高爐爐碴 |
|
|
|
CNS 8260
2019 Edition Method of Endurance Test Code of Carburetors for Automobiles 汽車用化油器耐久性能試驗法 |
|
|
|
CNS 10500
2019 Edition General Rules for X-Ray Fluoerscence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法通則 |
|
|
|
CNS 3376-2
2019 Edition Explosive atmospheres - Part 2: Equipment protection by pressurized enclosure〝p〞 爆炸性環境－第２部：正壓外殼構造〝ｐ〞之設備保護 |
|
|
|
CNS 10986
2019 Edition Method of test for safety glazing materials for road vehicles 汽車用安全玻璃檢驗法 |
|
|
|
CNS 60669-2-2
2019 Edition Switches for household and similar fixed electrical installations − Part 2-2: Particular requirements − Electromagnetic remote-control switches (RCS) 家用和類似用途固定式電氣裝置之開關－第2-2部：電磁式遙控開關(RCS)之個別要求 |
|
|
|
CNS 14562
2019 Edition High density rigid foam urethane for heat insulating 高密度硬質聚胺基甲酸酯發泡塑膠隔熱墊 |
|
|
|
CNS 15171
2019 Edition Method of test for flat particles, elongated particles, or flat and elongated particles contents in coarse aggregate 粗粒料中扁平、細長或扁長顆粒含量試驗法 |
|
|
|
CNS 14545-8
2019 Edition Fire hazard testing-Part 2:Test methods-Section 2:Needle-flame test 火災危險性試驗－第２部：試驗方法－第２章：針焰試驗 |
|
|
|
CNS 15288
2019 Edition Method of test for total count of bacteria, yeast and mould of pulp, paper and board 紙漿、紙及紙板中細菌、酵母菌與黴菌菌落數測定法 |
|
|
|
CNS 16094-1
2019 Edition Ductile iron pipes, fittings, accessories and their joints − External zinc-baseD Coating − Part 1: Metallic zinc with finishing layer 延性鑄鐵管、管件、配件及接頭－外部鋅基塗層－第1部：金屬鋅及精整層 |
|
|
|
CNS 15207-4
2019 Edition Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 4: Bulk current injection (BCI) 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第４部：大電流注入 |
|
|
|
CNS 15109
2019 Edition Denatured fuel ethanol for blending with gasolines for use as automotive spark-ignition engine fuel 變性燃料乙醇（含生質酒精）－供汽油摻配作為汽車火花點火引擎燃料 |
Translated |
|
|
CNS 9439
2019 Edition Method for chemical analysis of silicon carbide abrasives 碳化矽磨料化學分析法 |
|
|
|
CNS 2119
2019 Edition Refined waterfowl feather and down 精製水禽羽 |
|
|
|
CNS 62552-2
2019 Edition Household refrigerating appliances − Characteristics and test methods − Part 2: Performances requirements 家用冷凍冷藏電器－特性及試驗法－第2部：性能要求 |
|
|
|
CNS 6368
2019 Edition Vinylon Blended Spun Yarns, Cotton System, Unfinished 維尼龍混紡紗（棉紡式，本白紗） |
|
|
|
CNS 1440
2019 Edition PVC Floor Sheets ( replaced by CNS 8906 ) 軟質聚氯乙烯塑膠片 |
Translated |
|
|
CNS 15562-9
2019 Edition Stationary training equipment − Part 9: Elliptical trainers, additional specific safety requirements and test methods 固定式訓練器材－第9部：橢圓訓練機之附加特定安全要求與試驗法 |
|
|
|
CNS 15120
2019 Edition Secondary cells and batteries for photovoltaic energy systems (PVES) − General requirements and methods of test 太陽光電能源系統用之二次單電池與電池組－一般要求與試驗法 |
|
|
|
CNS 15615
2019 Edition Information technology − Telecommunications and information exchange between systems − Near FielD Communication Interface and Protocol - 2 (NFCIP - 2) 資訊技術－系統間電信與資訊 交換－近場通訊介面與協定-2(NFCIP-2) |
|
|
|
CNS 11446-2
2019 Edition Methods of measurement on receives for television broadcast transmission-Part2: Audio channels-General methods and methods for monophnic channels 電視廣播傳輸接收機之量測方法-第2部 : 聲道-一般方法與單聲道方法 |
|
|
|
CNS 16107-3
2019 Edition Hollow taper interface with flange contact surface − Part 3: Dimensions of shanks for stationary tools 具凸緣接觸面之空心錐度界面－第3部：固定式刀具之刀柄尺度 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [120] [121] [122] [123] [124] [125] [126] |
