"LA " CNS Standards List |
|
CNS 9105
1987 Edition Symbols of Electric machines of Interior Wiring Diagram for Architectural PLAns 屋內配線設計圖電機類符號 |
|
|
|
CNS 3070
1987 Edition InsuLAting Oil (for Cold Area) 絕緣油（寒地用） |
Translated |
|
|
CNS 9103
1987 Edition Symbols of ReLAys of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電驛類符號 |
|
|
|
CNS 9102
1987 Edition Symbols of Switch of Interior Wiring Diagram for Architectural PLAns 屋內配線設計圖開關類符號 |
|
|
|
CNS 9101
1987 Edition Graphical Symbols of Interior Wiring Diagram for Architectural PLAns 屋內配線設計圖符號總則 |
|
|
|
CNS 11823
1987 Edition Glossary of Terms ReLAted to Nondestructive Testing (Eddly Current Testing Terms) 非破壞檢測詞彙（渦電流檢測名詞） |
|
|
|
CNS 6071
1987 Edition 600 V Silicon Rubber InsuLAted Glass Fiber Braided Wires 600 V矽橡膠絕緣玻璃纖維編織電線 |
Translated |
|
|
CNS 6064
1987 Edition InsuLAted Wire for Neon Tube 氖氣管用絕緣電線 |
Translated |
|
|
CNS 4366
1987 Edition Hexagon Bolts with LArge Widths Across Flats for Steel Structures (Joints with Hightensile, Prestressed Bolts) 六角頭螺栓（具大對面寬度、高預力連接鋼結構用） |
|
|
|
CNS 4079
1987 Edition Wire Spring ReLAy 線簧電驛 |
|
|
|
CNS 9106
1987 Edition Symbols of Potential Transformers and Current Transformers of Interior Wirign Diagram for Architectural PLAns 屋內配線設計圖變比器類符號 |
|
|
|
CNS 11932
1987 Edition Angle Pins of Molds for PLAstics 塑膠型模用角銷 |
|
|
|
CNS 9234
1987 Edition Method of Test for Dry Reed Switches (Standard Test Coils, Single InsuLAtion 130 ℃ Wire) 乾式簧開關檢驗法（130℃單層絕緣線標準試驗線圈） |
|
|
|
CNS 8871
1987 Edition Dental PLAster 牙科用普通石膏 |
|
|
|
CNS 8230
1987 Edition Method of Test for Dry Reed Switches (InsuLAtion Resistance) 乾式簧開關檢驗法（絕緣電阻） |
|
|
|
CNS 11828
1987 Edition Method of Test for BLAst Furnace Slag for Road Construction 道路用高爐爐碴檢驗法 |
Translated |
|
|
CNS 11898
1987 Edition Reliability Assured PLAstic Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for PLAstics 塑膠型模用頂出套筒 |
|
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for PLAstics 塑膠型模用頂出導銷 |
|
|
|
CNS 11934
1987 Edition Stop Bolts of Molds for pLAstics 塑膠型模用止動螺栓 |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for PLAstics 塑膠型模用支持座 |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for PLAstics 塑膠型模用止銷 |
|
|
|
CNS 8223
1987 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 41 CircuLAr Jacket Cable Flexing Test) 頻率3 MHz以下電連接器檢驗法（圓形護套電纜可撓性試驗TP-41） |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas FLAme Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 12122
1987 Edition Method of Test on Communication Receivers for Amplitude-ModuLAtion Transmissions 調幅通信接收機檢驗法 |
|
|
|
CNS 11937
1987 Edition Runner Pull Pins of Molds for PLAstics 塑膠型模用流道拉銷 |
|
|
|
CNS 12085
1987 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler LAunch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求FOTP-54） |
|
|
|
CNS 12074
1987 Edition FLAsh Cavity of Hot Forging Closed Die 熱鍛閉合模之餘料穴 |
|
|
|
CNS 12070
1987 Edition EjectorpLAte Guide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-LAunch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
| Find out:3991Items | To Page of: First -Previous-Next -Last | [120] [121] [122] [123] [124] [125] [126] |
