"46 " CNS Standards List |
|
CNS 14694-2
2017 Edition Audio , video and audiovisual systems-interconnections and matching values Part 2：21-pin connector for video systems-application No.2 聲音、影像及視聽系統之互連與匹配值－第２部：影像系統適用之２１針連接器－第２類應用 |
|
|
|
CNS 4660
2017 Edition Tommy Nuts with Fixed Clamping Bolt 貫頭螺帽（固定扳桿型） |
|
|
|
CNS 11572
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-46 Continuity Test) 頻率３ＭＨｚ以下電連接器檢驗法（連續性試驗ＴＰ–４６） |
|
|
|
CNS 14466-11
2017 Edition Audiovisual,video and television equipment and systems. Part11:Video recording systems-operation practices to facilitate browsing 視聽．影像及電視設備與系統-第１１部：影像記錄系統-用於瀏覽之操作實務 |
|
|
|
CNS 13046
2017 Edition General Rules of Chemical Analysis for Magnesium Alloys 鎂合金分析法通則 |
|
|
|
CNS 11646
2017 Edition Glassfiber reinforced plastic pipe for sewer and industrial use 污水與工業用玻璃纖維強化塑膠管 |
|
|
|
CNS 14685
2017 Edition Pulps - Preparation of laboratory sheets for measurement of reflectance 紙漿、紙及紙板表示性能之國際單位 |
|
|
|
CNS 3464
2017 Edition Method of Erichsen Cupping Test 艾氏凹壓試驗法 |
|
|
|
CNS 12246
2017 Edition Method of Test for Oil-Soluble 100% Phenolic Resins of Electricals Insulating 電絕緣塗料用１００％油溶性酚樹脂試驗法 |
|
|
|
CNS 14673
2017 Edition Interference to mobile radiocommunications in the presence of impulsive noise - Methods of judging degradation and measures to improve performance 脈衝性雜訊對行動無線通信的干擾－產品劣化的判定方式及其性能的改善方法 |
|
|
|
CNS 146
2017 Edition Height of Shaft, for Driving and Driven Lines 軸心高度，主動機及從動機 |
|
|
|
CNS 4665
2017 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 4653
2017 Edition Slotted Headless Screws with Full Dog Point 有槽無頭長柱端螺釘 |
|
|
|
CNS 4647
2017 Edition Square Taper Washers for High Prestressed Channels 斜墊圈（槽鐵高強度結構用） |
|
|
|
CNS 4690
2017 Edition Studs for Drawn Arc Stud Welding - T - Studs 電弧樁熔接用柱樁–Ｔ形樁 |
|
|
|
CNS 4649
2017 Edition Plain Thrust Bearings Tilting Pad Thrust Bearings Boundary Dimensions 硬化光墊圈 |
Translated |
|
|
CNS 4606
2017 Edition Studs, Metal End≈2.5d 螺樁（旋入端長 ≈2.5d） |
|
|
|
CNS 4698
2017 Edition Countersunk Double-rib Bolts and Counter Sinkings for Agricultural Equipment 平頂埋頭雙肋螺栓與錐坑（農業機械用） |
|
|
|
CNS 14623-1
2017 Edition Sterilization of health care products-chemical indicators-Part 1：General requirements 保健產品之滅菌─化學指示劑─第一部分：一般規定 |
|
|
|
CNS 4658
2017 Edition Tommy Screws with Fixed Clamping Bolt 貫頭螺釘（固定扳桿型） |
|
|
|
CNS 14672
2017 Edition Methods of measurement of the suppression characteristics of passive radio interference filters and suppression components 被動式射頻干擾濾波器和抑制元件特性之量測方法 |
|
|
|
CNS 4659
2017 Edition Tommy Screws with Movable Clamping Bolt 貫頭螺釘（滑動扳桿型） |
|
|
|
CNS 7346
2017 Edition Sand Shovel 沙鏟 |
|
|
|
CNS 3469
2017 Edition Metal Wedge 金屬楔 |
|
|
|
CNS 10646
2017 Edition Double-Pick up, Blacksmiths' Tongs 鍛工用雙葫蘆形夾鉗 |
|
|
|
CNS 4652
2017 Edition Slotted Headless Screws with Chamfered End 有槽無頭去角端螺釘 |
|
|
|
CNS 4657
2017 Edition Grub Screws with Thrust Point 無頭止推端螺釘 |
|
|
|
CNS 4662
2017 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 9462
2017 Edition Test Code for Performance of Bed Type Horizontal Milling Machines 床台型臥式銑床動態檢驗法 |
Translated |
|
|
CNS 14466-1
2017 Edition Audiovisual,video and television equipment and systems. Part1:General 視聽．影像及電視設備與系統-第１部：通則 |
|
| Find out:651Items | To Page of: First -Previous-Next -Last | [8] [9] [10] [11] [12] [13] [14] |
