"6 6 " CNS Standards List |
|
CNS 6617
2017 Edition Gold- Silver-Palladium Alloy Solders for Dental Use 牙科用金銀鈀合金焊料 |
|
|
|
CNS 4216
2017 Edition Wire Twister Pliers (with Side Cutter) 扭絲鉗（附邊剪器） |
Translated |
|
|
CNS 9621
2017 Edition Rubber hoses for liquefied petroleum gases (LPGs) − Automobile, general equipment and home application 液化石油氣用橡膠管(LPG 橡膠管)－汽車、一般設備及家庭用 |
|
|
|
CNS 6158
2017 Edition Method of Test for Electromechanical Switches(Sand and Dust) 電機開關檢驗法–沙及灰塵 |
|
|
|
CNS 11762
2017 Edition Environmental Requirements for Electronic Equipments 電子設備之使用環境條件 |
|
|
|
CNS 1476
2017 Edition Viscose Rayon Staple Fiber Woven Fabrics (Unfinished) 黏液嫘縈棉梭織物（漂染前） |
Translated |
|
|
CNS 12265
2017 Edition Method of Test for Aluminum Tri - Polyphosphate for Coating 塗料用三聚磷酸鋁檢驗法 |
|
|
|
CNS 15187-6
2017 Edition Low-voltage fuses - Part 6: Supplementary requirements for fuse-links for the protection of solar photovoltaic energy systems 低電壓熔線－第6部：太陽光電 能源系統保護用熔線鏈之補充規定 |
|
|
|
CNS 15329-6
2017 Edition Information technology - Radio frequency identification device conformance test methods - Part 6: Test methods for air interface communications at 860 MHz to 960 MHz 資訊技術－無線射頻識別裝置符合性測試方法－第６部：８６０ＭＨｚ至９６０ＭＨｚ空中介面通信之測試方法 |
|
|
|
CNS 4660
2017 Edition Tommy Nuts with Fixed Clamping Bolt 貫頭螺帽（固定扳桿型） |
|
|
|
CNS 4561
2017 Edition Cross Recessed Countersunk (Oval) Head Screws 十字穴扁圓頂埋頭螺釘 |
Translated |
|
|
CNS 2864
2017 Edition Deep Groove Thrust Ball Bearings Single-Thrust, with Flat Seating 深溝止推滾珠軸承（單向具平面座外環） |
|
|
|
CNS 6700
2017 Edition LIGHT WIGHT RESCUE APPARATUS 簡便氧氣呼吸器 |
|
|
|
CNS 6628
2017 Edition Finger Sack for Medical Use 醫療用指套 |
|
|
|
CNS 7167
2017 Edition Method of Test for Hydroxyl Value of Fatty Oils and Acids 脂肪油及脂肪酸羥價測定法 |
|
|
|
CNS 13163
2017 Edition Method of Soundness Test for Fillet Welds 填角熔接部之無瑕疵試驗法 |
|
|
|
CNS 6399
2017 Edition Dental Wrought Gold - Silver - Palladium Alloy 牙科用鍛造金銀鈀合金 |
|
|
|
CNS 12986
2017 Edition Sizes of Untrimmed Paper 裁切前原紙尺度 |
Translated |
|
|
CNS 15776-1
2017 Edition Energy management system application program interface (EMS-API) – Part 1: Guidelines and general requirements 能源管理系統應用程式介面－第1部：指導綱要及一般要求事項 |
|
|
|
CNS 7962
2017 Edition Test Code for Performance of Numerically Controlled Table Type Horizontal Boring Machines 數值控制床台型臥式搪床動態檢驗法 |
|
|
|
CNS 14368
2017 Edition Micrographics-Recommendations for the creation of original documents 微縮技術－製作原始文件的建議 |
|
|
|
CNS 6004
2017 Edition Agricultural Tactors and Machines-Symbols for Operator Controls 農業機械之操作標示符號 |
|
|
|
CNS 6135-6
2017 Edition Hearing aids-Part6: Characteristics of electrical input circuit for hearing aids 助聽器－第6部:電氣輸入電路的特性 |
|
|
|
CNS 4647
2017 Edition Square Taper Washers for High Prestressed Channels 斜墊圈（槽鐵高強度結構用） |
|
|
|
CNS 13622
2017 Edition Fixed chip resistor for use in electronic equipment 電子設備用固定晶片電阻器 |
|
|
|
CNS 10226
2017 Edition Test code for accuracy of wide belt sanders 寬帶砂光機精度檢驗 |
|
|
|
CNS 15625-2
2017 Edition Paragliding equipment – Paragliders – Part 2: Requirements and test methods for classifying flight safety characteristics 飛行傘設備─飛行傘─第2部：飛行安全性分類要求與試驗法 |
|
|
|
CNS 4564
2017 Edition Cross Recessed Raised Countersunk (Oval) Head Wood Screws 十字穴扁圓頂埋頭木螺釘 |
Translated |
|
|
CNS 7166
2017 Edition Method of Test for Color After Heating of Fatty Acids 脂肪酸加熱後之顏色檢驗法 |
|
|
|
CNS 15528
2017 Edition Plastic Cup ( replaced by CNS 2446 ) 塑膠吸管 |
|
| Find out:5911Items | To Page of: First -Previous-Next -Last | [126] [127] [128] [129] [130] [131] [132] |
