"D C " CNS Standards List| General rules | Half round | Method test | Bolts T | Method test | Sets High | Safety requirements | Dimensions Racks | |
|
CNS 15642
2019 Edition RigiD Cellular plastics – Determination of water absorption 硬質發泡塑膠－吸水率測定法 |
|
|
|
CNS 14394
2019 Edition Clip-on valves for liquefied petroleum gases 液化石油氣用夾套式鋼瓶閥 |
|
|
|
CNS 8961
2019 Edition Marine Cast Iron 16 kgf/㎠ Screw-down Check Globe Valves 船用鑄鐵螺桿止回球形閥（16 kgf/㎠） |
|
|
|
CNS 15711-2
2019 Edition Photovoltaic (PV) module performance testing and energy rating − Part 2: Spectral responsivity, incidence angle and module operating temperature measurements 太陽光電模組性能試驗及能量定額－第2部：光譜響應度、入射角及模組操作溫度量測 |
|
|
|
CNS 8259
2019 Edition Method of Fuel Leakage Test of Carburetors for Automobiles 汽車用化油器燃料洩漏性能試驗法 |
|
|
|
CNS 8825
2019 Edition Marine Cast Iron 10 kgf/㎠ Screw - Down Check Globe Valves 船用鑄鐵螺桿止回球形閥（10 kgf/㎠） |
|
|
|
CNS 7270
2019 Edition Method of Test for Vinylon Ropes 維尼龍繩索檢驗法 |
|
|
|
CNS 4061
2019 Edition ReinforceD Concrete Ditches (U Type) 鋼筋混凝土Ｕ形溝 |
Translated |
|
|
CNS 14904
2019 Edition Essential oils - General guidance on the determination of flashpoint 精油－閃點測定法 |
|
|
|
CNS 15105
2019 Edition Textiles - Determination of abrasion resistance of fabrics by the Martindale method - Part 3 : Determination of mass loss 紡織品耐摩損性馬丁代爾試驗法－第３部：質量減損試驗法 |
|
|
|
CNS 15668
2019 Edition Size designation of clothes 服裝尺碼標示 |
|
|
|
CNS 964
2019 Edition Dentistry – Manual toothbrushes – General requirements and test methods 牙科－手動牙刷－一般要求及試驗法 |
|
|
|
CNS 3905
2019 Edition Concrete pipes for sewerage (Use for jacking method) 下水道用鋼筋混凝土管 （推進施工法用） |
|
|
|
CNS 5846-1
2019 Edition Plastics - Determination of ash - Part 5: Poly (vinyl chloride) 塑膠－沙丕(Charpy)衝擊性能測定法－第1部：非儀器式衝擊試驗 |
|
|
|
CNS 15876-7
2019 Edition Specification and qualification of welding procedures for metallic materials − Welding procedure test − Part 7: Overlay welding 金屬材料銲接程序規範書及其檢定－銲接程序試驗－第7部：堆銲 |
|
|
|
CNS 62782
2019 Edition Photovoltaic (PV) modules − Cyclic (dynamic) mechanical load testing 太陽光電模組－循環(動態)機械負荷試驗 |
|
|
|
CNS 5433
2019 Edition Method of Test for Hydraulic Trolley Jacks for Automobiles 汽車用輕便式輪型液壓千斤頂檢驗法 |
Translated |
|
|
CNS 15600
2019 Edition Photovoltaic devices - Procedures for temperature and irradiance corrections to measured I-V characteristics 太陽光電裝置－量測I-V特性之溫度與照射度修正程序 |
|
|
|
CNS 10157
2019 Edition Selection of Fuses and Fusible-Links for Automobile Wiring 汽車用迴路保險絲及易熔鏈之選用 |
|
|
|
CNS 15187-4
2019 Edition Low-voltage fuses - Part 4: Supplementary requirements for fuse-links for the protection of semiconductor devices 低壓熔線－第４部︰半導體裝置保護用熔線鏈之補充規定 |
|
|
|
CNS 3473
2019 Edition Hydraulic brake wheel cylinders for automobiles 汽車用液壓煞車分泵 |
|
|
|
CNS 14129
2019 Edition Method of random vibration test for vehicle parts 車輛零組件隨機振動試驗法 |
|
|
|
CNS 4711
2019 Edition General rules of fixed resistors for use in electronic equipment 電子設備用固定電阻器通則 |
|
|
|
CNS 4681
2019 Edition Canned tomato katsup 番茄醬罐頭 |
|
|
|
CNS 15061
2019 Edition Diesel and domestic heating fuels - Determination of cold filter plugging point 柴油及家用加熱燃油－冷濾點測定法 |
|
|
|
CNS 1163
2019 Edition Method of test for bulk density and voids in aggregate 粒料容積密度與空隙率試驗法 |
|
|
|
CNS 6694
2019 Edition Polyacrylonitrile Blended Yarns, Cotton System, Finished 聚丙烯月青混紡紗（梳毛式，漂染紗） |
|
|
|
CNS 4160
2019 Edition Method of Ferroxyl Test for Surface Finishing 表面處理用鐵氰錯鹽試驗法 |
|
|
|
CNS 9991
2019 Edition Fixed Design and Method of Use for Oil Seals for Automobiles 汽車用油封安裝部位之設計及使用方法 |
|
|
|
CNS 4750
2019 Edition Tubular steel scaffolds 鋼管施工架 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [134] [135] [136] [137] [138] [139] [140] |
