"D " CNS Standards List |
|
CNS 13785
2019 Edition MethoDs of Test for Synthetic Filament Textured Yarns 合成絲狀纖維加工紗試驗法 |
|
|
|
CNS 697
2019 Edition ActivateD Carbon Powder for Industrial Use 工業用活性碳（粉狀） |
|
|
|
CNS 3787
2019 Edition CoateD abrasivse grain sizes 砂紙、砂布用磨料粒度 |
|
|
|
CNS 8241
2019 Edition MethoD of Starting Test of Carburetors for Automobiles 汽車用化油器起動性能試驗法 |
|
|
|
CNS 15755-5-5
2019 Edition Conversion tables for units − Part 5-5: Pressure or stress − Millimeter of mercury anD standard atmosphere 單位換算表－第5-5 部：壓力或應力－毫米汞柱與標準大氣壓 |
|
|
|
CNS 14840
2019 Edition MethoD of test for passability through obstacles of self-compacting concrete 自充填混凝土障礙通過性試驗法（Ｕ形或箱形法） |
|
|
|
CNS 3813
2019 Edition Marine Cast Iron 10 kgf/㎠ Screw-Down Check Angle Valves 船用鑄鐵旋緊止回角閥（10 kgf/㎠） |
|
|
|
CNS 15336
2019 Edition Furniture - MethoD of determination for strength and durability of table 家具－桌子強度與耐久性測定法 |
|
|
|
CNS 10573
2019 Edition GraDes of Heng Shan Pear 橫山梨等級 |
Translated |
|
|
CNS 15683
2019 Edition StanDard representation of geographic point location by coordinates 地理點位置之座標標準表示法 |
|
|
|
CNS 5433
2019 Edition MethoD of Test for Hydraulic Trolley Jacks for Automobiles 汽車用輕便式輪型液壓千斤頂檢驗法 |
Translated |
|
|
CNS 5432
2019 Edition HyDraulic Trolley Jacks for Automobiles 汽車用輕便式輪型液壓千斤頂 |
Translated |
|
|
CNS 14545-1
2019 Edition Fire hazarD testing-part 1:Guidance for assessing fire hazard of electrotechnical products(general guidance) 火災危險性試驗－第１部：評估電氣產品火災危險性的指引（通則） |
|
|
|
CNS 6187
2019 Edition Paints, varnishes anD plastics − Determination of non-volatile-matter content 油漆、清漆及塑膠－不揮發物含量測定法 |
|
|
|
CNS 15593-31
2019 Edition Electricity metering – Data exchange for meter reading, tariff and load control – Part 31: Use of local area networks on twisted pair with carrier signalling 電力計量－ 讀表、計費及負載控制之資料交換－ 第31 部： 使用雙絞線載波信號之區域網路 |
|
|
|
CNS 3290
2019 Edition Piano wire roDs 鋼琴線 |
|
|
|
CNS 13865
2019 Edition Symbols of instruments anD controls for automobiles 汽車儀表及控制器標誌 |
|
|
|
CNS 16097-1
2019 Edition Machine tools − Dimensions and geometric tests for self-centring chucks with two-piece jaws − Part 1: Manually operated chucks with tongue and groove type jaws 工具機－具兩件式夾爪之自定心夾頭的尺度及幾何試驗－第1部：具榫槽式夾爪之手動操作夾頭 |
|
|
|
CNS 10856
2019 Edition General Rules for Environmental Tests of Control anD Instrumentation Equipment for Marine Use 船用自動控制機器環境檢驗通則 |
|
|
|
CNS 60670-1
2019 Edition Boxes anD enclosures for electrical accessories for household and similar fixed electrical installations − Part 1: General requirements 家用及類似用途固定安裝電氣配件用箱體及外殼－第1部：一般要求 |
|
|
|
CNS 14896-3
2019 Edition Titanium anD titanium alloys - Methods for determination of iron content 鈦及鈦合金－鐵定量法 |
|
|
|
CNS 15228-7
2019 Edition Test methoDs for lead-free solders - Part 7: Shear strength of solder joints on surface-mounted devices 無鉛銲錫試驗法－第７部：表面黏著元件上銲錫接點之剪力強度試驗法 |
|
|
|
CNS 14395
2019 Edition Clip on regulator for liquefieD petroleum gas 液化石油氣用夾套式調整器 |
|
|
|
CNS 13953
2019 Edition MethoD of test for hydraulic brake systems 液壓煞車系統試驗法 |
|
|
|
CNS 6693
2019 Edition Polyacrylonitrile BlenDed Yarns, Worsted System, Finished 聚丙烯月青混紡紗（梳毛式，本白紗） |
|
|
|
CNS 11064
2019 Edition Injection Nozzle HolDer Type P for Road Vehicles (with Body and with Fixing FLats) 汽車用Ｐ型燃料噴油嘴固定器 |
|
|
|
CNS 11012
2019 Edition Iron anD steel - General rules for analytical methods 鐵及鋼－分析法通則 |
|
|
|
CNS 15064-1
2019 Edition Solar energy - Reference solar spectral irraDiance at the ground at different receiving conditions - Part 1: Direct normal and hemispherical solar irradiance for air mass 1.5 太陽能－在不同地球表面接收狀況下之參考太陽光譜照射度－第１部：大氣光程１﹒５下之直接垂直與半球太陽照射度 |
|
|
|
CNS 15069
2019 Edition IPv6 stateless aDdress autoconfiguration ＩＰｖ６不具狀態的位址自動組態設定 |
|
|
|
CNS 16107-1
2019 Edition Hollow taper interface with flange contact surface − Part 1: Shanks − Dimensions 具凸緣接觸面之空心錐度界面－第1部：刀柄尺度 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [135] [136] [137] [138] [139] [140] [141] |
