"LE " CNS Standards List |
|
CNS 4665
2017 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead HoLE 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 8195
2017 Edition Method of Test for Subplate Type SoLEnoid Operated 4 - Port Valves (Oil - Hydraulic Use ) 液壓用副板型四通電磁操作閥檢驗法 |
|
|
|
CNS 14182
2017 Edition Reliability and lot control tests for analog video laser transmitter and receiver moduLEs used for optical fiber communication 光纖通信用類比視訊雷射傳輸和接收模組之可靠度及批品質控制測試 |
|
|
|
CNS 8937
2017 Edition Method of Test for Travelling CabLEs for Elevators 升降機用移動電纜檢驗法 |
|
|
|
CNS 13982-16
2017 Edition Methods of test for bulk down and feather − Part 16: Determination of durabLE water repellent treatments 羽絨羽毛試驗法－第16部：耐久撥水處理測定法 |
|
|
|
CNS 15226
2017 Edition SingLE-use sterile rubber gloves - Specification 單次使用之無菌橡膠手套－規格 |
|
|
|
CNS 12439
2017 Edition Coil Impregnating Varnishers for ELEctrical Insulation 電絕緣用線圈浸漬清漆 |
|
|
|
CNS 3873
2017 Edition Method of Test for the Rear Hubs of BicycLEs 自行車（腳踏車）後輪轂檢驗法 |
Translated |
|
|
CNS 9367
2017 Edition Method of Test for Low Frequency (Below 3 MHz) ELEctrical Connectors (TP - 14 Ozone Exposure) 頻率３ＭＨｚ以下電連接器檢驗法（耐臭氧試驗ＴＰ–１４） |
|
|
|
CNS 14685
2017 Edition Pulps - Preparation of laboratory sheets for measurement of refLEctance 紙漿、紙及紙板表示性能之國際單位 |
|
|
|
CNS 14673
2017 Edition Interference to mobiLE radiocommunications in the presence of impulsive noise - Methods of judging degradation and measures to improve performance 脈衝性雜訊對行動無線通信的干擾－產品劣化的判定方式及其性能的改善方法 |
|
|
|
CNS 12865-9
2017 Edition Method of Test for Digital MicroeLEctronics ( Delay Measurements ) 數位微電子檢驗法（延遲量測） |
|
|
|
CNS 768
2017 Edition BoiLEd Linseed Oil 熟煉亞麻仁油 |
Translated |
|
|
CNS 4698
2017 Edition Countersunk DoubLE-rib Bolts and Counter Sinkings for Agricultural Equipment 平頂埋頭雙肋螺栓與錐坑（農業機械用） |
|
|
|
CNS 3607
2017 Edition SingLE Angle Milling Cutters with Threaded Holes 附螺紋孔單側角銑刀 |
Translated |
|
|
CNS 11112
2017 Edition Methods of Chemical Analysis for LEad Ingot 鉛錠分析法 |
|
|
|
CNS 9796
2017 Edition SaddLE supported horizontal pressure vessels 以鞍座支撐之臥型壓力容器 |
|
|
|
CNS 12519
2017 Edition Metal SpectacLE Frames 金屬眼鏡架 |
|
|
|
CNS 10237
2017 Edition HandLEs for Cranes 起重機用手柄 |
|
|
|
CNS 14266
2017 Edition CabLE management systems – Cable ties for electrical installations 電纜管理系統 - 電氣設備用 電纜束線帶 |
|
|
|
CNS 1212
2017 Edition Triangular Saw FiLE Thin Type 薄三角形磨鋸銼 |
Translated |
|
|
CNS 3603
2017 Edition SingLE Angle Milling Cutters 單側角銑刀 |
Translated |
|
|
CNS 13350-8
2017 Edition The Safety Code of Mechanical Parking Lot Devices (SimpLE Elevator Type) 機械式停車場安全標準（簡易升降式） |
|
|
|
CNS 7004
2017 Edition ParalLEl Shank Twist Drills for Use in Jig Bushes 鑽模導套用蔴花鑽（圓柱柄） |
|
|
|
CNS 11572
2017 Edition Method of Test for Low Frequency (Below 3MHz) ELEctrical Connectors (TP-46 Continuity Test) 頻率３ＭＨｚ以下電連接器檢驗法（連續性試驗ＴＰ–４６） |
|
|
|
CNS 328
2017 Edition Straight Wrench LEver 直扳柄 |
|
|
|
CNS 12653
2017 Edition Evaporator for Liquefied PetroLEum Gas Use 液化石油氣用蒸發器 |
Translated |
|
|
CNS 10698
2017 Edition Method of Test for Land MobiLE Communication FM or PM Receivers, 25-947 MHz (Squelch Blocking, Receiver Attack and Closing Time) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（靜音截斷、接收機動作及閉合時間） |
|
|
|
CNS 6151
2017 Edition Method of Test for ELEctromechanical Switches(Overload) 電機開關檢驗法–過負荷 |
|
|
|
CNS 15966
2017 Edition Packaging − Child resistant packaging − Mechanical test methods for reclosabLE child resistant packaging systems 包裝−防止兒童開拆之包裝−防止兒童開拆之可重複包裝系統機械試驗法 |
|
| Find out:6143Items | To Page of: First -Previous-Next -Last | [137] [138] [139] [140] [141] [142] [143] |
