"2 " CNS Standards List |
|
CNS 13092
2017 Edition Measuring Method for LED Outdoor Display Panels 發光二極體顯示幕（戶外用）量測法 |
|
|
|
CNS 5502
2017 Edition Cylindrical Roller Bearings; with Ribs on Outer Ring, Single Row 滾柱軸承（單列具導肋外環） |
|
|
|
CNS 9621-3
2017 Edition Rubber hoses for liquefied petroleum gases (LPGs) - Part 3: Dispensing hoses and hose assemblies 液化石油氣用橡膠管(LPG橡膠管)－第3部：加氣用管及管組合件 |
|
|
|
CNS 13623
2017 Edition Test Methods for Measuring Resistivity,Hall Coefficient and Determining Hall Mobility in Single-Crystal Semiconductors(Van Der Pauw Method) 單晶片之電阻率、霍爾係數及霍爾移動率之測定法（范德普法） |
|
|
|
CNS 12291
2017 Edition General Rules for Reliability Assured Fixed Carbon Composition Resistors 可靠度保證混合碳固定電阻器總則 |
|
|
|
CNS 12846
2017 Edition Helium Mass Spectrometer Leak Testing by Trace Probe Method 氦質譜儀示蹤氣探針探漏法 |
|
|
|
CNS 3372
2017 Edition Hand Taps for Unified Coarse Thread, Class 3 統一制粗牙手力螺絲攻，精度３級 |
Translated |
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 2571
2017 Edition Safety Code for Storage Transporation and Use of Liquefied Chlorine 液氯儲運使用安全規章 |
|
|
|
CNS 5772
2017 Edition Thermistor Disks, Insulated (Style TDC) 盤形絕緣熱敏電阻器（型號ＴＤＣ） |
|
|
|
CNS 13621
2017 Edition Polyamide (Nylon) Textured Yarns 聚醯胺樹脂接線盒 |
Translated |
|
|
CNS 503
2017 Edition ISO Metric Fine Screw Threads (Diameters from 18 to 150mm and Pitch 2mm) 公制細螺紋6（ISO制）（標稱直徑18至150公釐，螺距2公釐） |
|
|
|
CNS 15421
2017 Edition Office furniture - Chairs 辦公室用椅 |
|
|
|
CNS 6152
2017 Edition Method of Test for Electromechanical Switches(Electrical Endurance) 電機開關檢驗法–電耐久性 |
|
|
|
CNS 12867
2017 Edition Basic Environmental Testing Procedures Part 2 : Tests-Test Z/AM : Combined Dry Heat/Low Air Pressure Tests 環境試驗法（電氣、電子）–高溫／低氣壓複合試驗法 |
|
|
|
CNS 4727
2017 Edition Power quality measurement in power supply systems − Part 1: Power quality instruments 動力插秧機 |
Translated |
|
|
CNS 15832-1-1
2017 Edition Method of test for coating components − Part 1-1: General rule − Common test conditions 塗料成分試驗法－第1-1部：通則－一般試驗條件 |
|
|
|
CNS 13288
2017 Edition Basic Environmental Testing Procedures Part 2: Tests - Guidance on Change of Temperature Tests 環境試驗法（電氣、電子）–溫度變化試驗之指引 |
|
|
|
CNS 15499-2
2017 Edition Electrically propelled road vehicles – Safety specifications – Part 2: Vehicle operational safety means and protection against failures 電動推進道路車輛－安全規範－第2部:車輛操作安全方法及故障防護 |
|
|
|
CNS 15551-2
2017 Edition Ergonomics - Accessible design - Sound pressure levels of auditory signals for consumer products 人因工程－無障礙設計 - 消費 產品中聲音訊號之聲壓位準 |
|
|
|
CNS 4221
2017 Edition Metric Trapezoidal Screw Thread (Limits for Internal Screw Threads From 8mm to 100mm) 梯形螺紋（標稱直徑８ｍｍ至１００ｍｍ的內螺紋限界尺寸） |
|
|
|
CNS 13127
2017 Edition Metallic and Other Non -organic Coatings -General Rules for Stationary Outdoor Exposure Corrosion Tests 金屬和無機被覆–靜態戶外曝露腐蝕試驗通則 |
|
|
|
CNS 1021
2017 Edition Picks, One Flat End and One Taper End 十字鎬（一端為尖錐狀，一端為鋼撬狀） |
|
|
|
CNS 4122
2017 Edition Type A1 standard test block for ultrasonic testing 超音波檢測用Ａ１型標準規塊 |
|
|
|
CNS 10216
2017 Edition Glossary of terms used in pressure vessels 壓力容器之用詞 |
|
|
|
CNS 3402
2017 Edition Letter Pads 信箋 |
Translated |
|
|
CNS 9240
2017 Edition Method of Test for Low Freguency(Below 3 MHz) Electrical Connectors(TP - 18 Visual and Dimensional Inspection) 頻率３ＭＨｚ以下電連接器檢驗法（外觀及尺度檢查ＴＰ–１８） |
|
|
|
CNS 5376-21
2017 Edition Iron ores—Method for determination zinc content 鐵礦石－鋅定量法 |
|
|
|
CNS 14623-2
2017 Edition Sterilization of health care products-chemical indicators-Part 2：Test equipment and methods 保健產品之滅菌─化學指示劑─第二部分：測試設備與方法 |
|
|
|
CNS 16016-2
2017 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PP) − Part 1: General 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第2部：管 |
|
| Find out:6760Items | To Page of: First -Previous-Next -Last | [138] [139] [140] [141] [142] [143] [144] |
