"IC " CNS Standards List |
|
CNS 11070
2017 Edition General Rules of Determination for Carbon in MetallIC Materials 金屬材料中碳定量法通則 |
![]() |
|
|
CNS 4959
2017 Edition Retreaded pneumatIC tyres for commercial vehicles and their trailers 卡客車用翻新輪胎 |
![]() Translated |
|
|
CNS 501
2017 Edition ISO MetrIC Fine Screw Threads (Diameters From 8 to 30mm and Pitches 1 to 1.25mm) 公制細螺紋4(ISO制)(標稱直徑8至30公釐,螺距1至1.25公釐) |
![]() |
|
|
CNS 15539
2017 Edition GymnastIC equipment - Wall bars and lattice ladders 體操設備-壁面肋木架及格子梯 |
![]() |
|
|
CNS 12439
2017 Edition Coil Impregnating Varnishers for ElectrICal Insulation 電絕緣用線圈浸漬清漆 |
![]() |
|
|
CNS 11379
2017 Edition RadiographIC Test for Castings 鑄件射線檢測法 |
![]() |
|
|
CNS 11655
2017 Edition Method of Test for Glassfiber Reinforced PlastIC Water Tank 玻璃纖維強化塑膠儲水槽檢驗法 |
![]() |
|
|
CNS 5820
2017 Edition SilICa Powder (White Carbon) (for Rubber Use) 二氧化矽粉(橡膠用) |
![]() Translated |
|
|
CNS 516
2017 Edition MetrIC Buttress Screw Thread General Plan 公制鋸齒形螺紋(總則) |
![]() |
|
|
CNS 9193
2017 Edition VehICles for Fire Pumps 消防用水泵車 |
![]() |
|
|
CNS 11572
2017 Edition Method of Test for Low Frequency (Below 3MHz) ElectrICal Connectors (TP-46 Continuity Test) 頻率3MHz以下電連接器檢驗法(連續性試驗TP–46) |
![]() |
|
|
CNS 10693
2017 Edition Method of Test for Land Mobile CommunICation FM or PM Receivers, 25-947 MHz (Definition and Test Condition) 陸上行動通信用25–947MHz調頻/調相接收機檢驗法(定義、試驗條件) |
![]() |
|
|
CNS 9125
2017 Edition Method of test for cables and flexible cords for electrICal equipment of ships 船舶電器設備用電線電纜檢驗法 |
![]() |
|
|
CNS 14623-1
2017 Edition Sterilization of health care products-chemICal indicators-Part 1:General requirements 保健產品之滅菌─化學指示劑─第一部分:一般規定 |
![]() |
|
|
CNS 3464
2017 Edition Method of ErIChsen Cupping Test 艾氏凹壓試驗法 |
![]() |
|
|
CNS 12996
2017 Edition Method of Determination for Contents of MetallIC Elements of Hardmetals by X-Ray Fluorescence (Fusion Method) 超硬合金金屬元素含量測定法–X射線螢光分析法(熔融法) |
![]() |
|
|
CNS 11646
2017 Edition Glassfiber reinforced plastIC pipe for sewer and industrial use 污水與工業用玻璃纖維強化塑膠管 |
![]() |
|
|
CNS 5197
2017 Edition PhotometrIC Measurement on Standard Fluorescent Lamps 標準螢光管光通量測定法 |
![]() |
|
|
CNS 10698
2017 Edition Method of Test for Land Mobile CommunICation FM or PM Receivers, 25-947 MHz (Squelch Blocking, Receiver Attack and Closing Time) 陸上行動通信用25–947MHz調頻/調相接收機檢驗法(靜音截斷、接收機動作及閉合時間) |
![]() |
|
|
CNS 13804
2017 Edition Guidance on the Use of the Substitution Method for Measurements of Radiation from MICrowave Ovens for Frequencies above 1 GHz 應用置換法測量微波爐1GHz以上之輻射指引 |
![]() Translated |
|
|
CNS 4665
2017 Edition Insert Nuts Heavy Type for PlastICs Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽(長型封閉式,嵌於塑膠製品與壓鑄件內用) |
![]() |
|
|
CNS 14179
2017 Edition Reliability tests for digital transmitter and receiver modules used for optICal fiber communication 光纖通信用數位傳輸和接收模組之可靠度測試 |
![]() |
|
|
CNS 14266
2017 Edition Cable management systems – Cable ties for electrICal installations 電纜管理系統 - 電氣設備用 電纜束線帶 |
![]() |
|
|
CNS 9367
2017 Edition Method of Test for Low Frequency (Below 3 MHz) ElectrICal Connectors (TP - 14 Ozone Exposure) 頻率3MHz以下電連接器檢驗法(耐臭氧試驗TP–14) |
![]() |
|
|
CNS 6151
2017 Edition Method of Test for ElectromechanICal Switches(Overload) 電機開關檢驗法–過負荷 |
![]() |
|
|
CNS 302
2017 Edition Hand Tap, MetrIC 公制絲公,手用 |
![]() Translated |
|
|
CNS 13575-3
2017 Edition Wheelchairs - Type ClassifICation based on appearance characteristics 輪椅–依外觀特性分類 |
![]() |
|
|
CNS 14182
2017 Edition Reliability and lot control tests for analog video laser transmitter and receiver modules used for optICal fiber communication 光纖通信用類比視訊雷射傳輸和接收模組之可靠度及批品質控制測試 |
![]() |
|
|
CNS 15210-6
2017 Edition Information technology - Radio frequency identifICation for item management - Part 6: Parameters for air interface communications at 860MHz to 960MHz 資訊技術─品項管理之無線射頻識別─第6部:860MHz至960MHz空中介面通信參數 |
![]() |
|
|
CNS 9209
2017 Edition VICkers Hardness Testing Machines 維克氏硬度試驗機 |
![]() |
Find out:6418Items | To Page of: First -Previous-Next -Last | [141] [142] [143] [144] [145] [146] [147] |