"3, " CNS Standards List| Method Test | Steering Bearings | Industrial automation | Internet Things | Picks, Illustration | Plain Washers, | Ergonomics − | Method Test | |
|
CNS 4563
2017 Edition Cross Recessed Countersunk (Flat) Head Wood Screws 十字穴平頂埋頭木螺釘 |
Translated |
|
|
CNS 15623
2017 Edition Paragliding equipment – Emergency parachutes – Safety requirements and test methods 飛行傘設備－緊急降落傘－安全要求與試驗法 |
|
|
|
CNS 1394
2017 Edition Cemet Sack Paper 水泥袋紙 |
Translated |
|
|
CNS 13423
2017 Edition Method of Test for Steel Cord Conveyor Belts 鋼索心體輸送橡膠帶檢驗法 |
|
|
|
CNS 3975
2017 Edition Flat Chisels 扁鑿 |
Translated |
|
|
CNS 13059-6
2017 Edition Photovoltaic devices Par 6:Requirements for reference solar modules 光電伏打元件（第六部：基準太陽電池模組之要求） |
|
|
|
CNS 15539
2017 Edition Gymnastic equipment - Wall bars and lattice ladders 體操設備－壁面肋木架及格子梯 |
|
|
|
CNS 13394
2017 Edition Method of Test for Viscosity of Pulp (Falling Ball Method) 紙漿黏度試驗法（落球法） |
Translated |
|
|
CNS 13727
2017 Edition Method of Test for Volume Resistivity of Conductive Adhesives 導電膠之體積電阻率量測法 |
|
|
|
CNS 13999
2017 Edition General methods of measuring the performances of ultrasonic pulse-echo diagnostic equipment 脈衝式反射法超音波診斷裝置檢驗法 |
|
|
|
CNS 504
2017 Edition ISO Metric Fine Screw Threads (Diameters from 30 to 250 mm and Pitch 3 mm) 公制細螺紋7（ISO制）（標稱直徑30至250公釐，螺距3公釐） |
|
|
|
CNS 6135-1
2017 Edition Hearing aids-Part1: Hearing aids with induction pick-up coil input 助聽器－第1部:以感應拾波線圈為輸入的助聽器 |
|
|
|
CNS 130
2017 Edition Morse Taper Gauge, Without Flat Head 莫氏圓錐量規（無扁頭） |
|
|
|
CNS 13377
2017 Edition Boron Steel Wire Rods for Cold Heading and Cold Forging 冷打及冷鍛用硼鋼線料 |
|
|
|
CNS 13055
2017 Edition Methods of Determination for Zisconium in Magnesium Alloys 鎂合金中鋯定量法 |
|
|
|
CNS 11395
2017 Edition Method of Test for Stiffness of Paper and Paperboard(Taber Stiffness Tester) 紙及紙板剛度試驗法（Ｔａｂｅｒ剛度試驗機） |
Translated |
|
|
CNS 9240
2017 Edition Method of Test for Low Freguency(Below 3 MHz) Electrical Connectors(TP - 18 Visual and Dimensional Inspection) 頻率３ＭＨｚ以下電連接器檢驗法（外觀及尺度檢查ＴＰ–１８） |
|
|
|
CNS 3446
2017 Edition Method of test for milk and milk products - Determination of sucrose content 乳品檢驗法－蔗糖之測定 |
|
|
|
CNS 3183
2017 Edition Method of test for residues in liquefied petroleum gases 液化石油氣殘餘物試驗法 |
|
|
|
CNS 3867
2017 Edition Method of Test for the Front Hubs of Bicycles 自行車（腳踏車）前輪轂檢驗法 |
Translated |
|
|
CNS 4103
2017 Edition Chain Pipe Wrenches 鏈條管鉗 |
Translated |
|
|
CNS 12243
2017 Edition Pilot Ladder 衝壓加工先導桿 |
|
|
|
CNS 6312
2017 Edition Roller Bearings for Electric Traction, Felt Ring and Felt Ring Grooves 電力牽引器用滾柱軸承毛氈填封與填封槽 |
|
|
|
CNS 4730
2017 Edition Lifting Eye Nuts 圓形環首螺帽 |
|
|
|
CNS 5376-19
2017 Edition Iron ores－Method for determination of arsenic content 鐵礦石－砷定量法 |
|
|
|
CNS 6398
2017 Edition Cobalt - Chromium Alloy Wires for Dental Use 牙科用鈷鉻合金線 |
|
|
|
CNS 13059-3
2017 Edition Photovoltaic Devices Part 3：Measurement Principles for Terrestrial Photovoltaic (PV) Solar Devices with Reference Spectral Irradiance Data 光電伏打元件（第三部：具光譜照射光參考數據之陸上光電伏打（ＰＶ）太陽元件量測原理） |
|
|
|
CNS 13804
2017 Edition Guidance on the Use of the Substitution Method for Measurements of Radiation from Microwave Ovens for Frequencies above 1 GHz 應用置換法測量微波爐１ＧＨｚ以上之輻射指引 |
Translated |
|
|
CNS 13249
2017 Edition Conformity assessment - Guidance on a third-party certification system for products 符合性評鑑－第三者產品驗證 系統指引 |
|
|
|
CNS 15832-2-1
2017 Edition Method of test for coating components − Part 2-1: Component analysis in solvent soluble matter − Acid value (Titrimetric method) 塗料成分試驗法－第2-1部：溶劑可溶物中成分分析－酸價(滴定法) |
|
| Find out:6360Items | To Page of: First -Previous-Next -Last | [142] [143] [144] [145] [146] [147] [148] |
