"3 " CNS Standards List |
|
CNS 13992
2017 Edition Fixed resistor networks in which not all resistors are individually measurable for use in electronic equipment 電子設備用不可單獨量測所有電阻元件之固定網路電阻器 |
|
|
|
CNS 9308
2017 Edition Method of test for colour fastness to potting 耐煮呢處理染色堅牢度試驗法 |
|
|
|
CNS 13507
2017 Edition Methods of Test for Glass - Fibor - Reinferced Plastic Pipe Fittings 玻璃纖維強化塑膠管配件檢驗法 |
Translated |
|
|
CNS 13075
2017 Edition Non-invasive automated sphygmomanometers 非侵入式自動血壓計 |
|
|
|
CNS 7283
2017 Edition Methods for Determination of Glod and Silver in Oxide Ores 氧化礦中金及銀定量法 |
|
|
|
CNS 3198
2017 Edition Silicon Sand (for Castings) 矽砂（鑄造用） |
|
|
|
CNS 3633
2017 Edition Basic Environmental Testing Procedures Part 2: Tests, Test N: Change of Temperature 環境試驗法（電氣、電子）–溫度變化試驗 |
|
|
|
CNS 3897
2017 Edition Marbles 大理石材 |
Translated |
|
|
CNS 12832
2017 Edition Method of Test for the Water Content of Freshly Mixed Concrete 新拌混凝土含水量試驗法 |
|
|
|
CNS 13249
2017 Edition Conformity assessment - Guidance on a third-party certification system for products 符合性評鑑－第三者產品驗證 系統指引 |
|
|
|
CNS 312
2017 Edition Tap Adapter 絲公接桿 |
|
|
|
CNS 3908
2017 Edition Method of Test for Wiring Devices 配線器具之試驗法 |
|
|
|
CNS 13566
2017 Edition Practice for Comparison of Spray Patterns of Aerosol Products 微縮品製作–拍攝文件第一代銀鹽片之作業程序、檢驗與品質管制 |
|
|
|
CNS 13579
2017 Edition Fire Hydrant Valves 消防栓閥 |
|
|
|
CNS 11575
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-55 Current Cycling Test) 頻率３ＭＨｚ以下電連接器檢驗法（電流循環試驗ＴＰ–５５） |
|
|
|
CNS 13037
2017 Edition Covered electrodes for atmospheric corrosion resisting steel 耐候性鋼用被覆銲條 |
|
|
|
CNS 3563
2017 Edition Method of Test for Low Elongation Stress of Vulcanized Rubber 硫化橡膠低伸長應力試驗法 |
|
|
|
CNS 6638
2017 Edition Supplied - Air Respirators 輸氣管面具 |
|
|
|
CNS 14384-2
2017 Edition Protective gloves against chemicals and micro-organisms - Part 1:Terminology and performance requirements 化學藥品及微生物防護手套－抗穿透性之測定 |
|
|
|
CNS 13252
2017 Edition Method of Tension Test for Spot Welded Joints 點熔接接合之拉伸試驗法 |
|
|
|
CNS 10643
2017 Edition Curved Lip, Fluted Jaw, Blacksmiths Tongs 鍛工用有槽顎夾夾鉗 |
|
|
|
CNS 9231
2017 Edition Method of Test for Dry Reed Switches(Physical Dimensions) 乾式簧開關檢驗法（實體尺度） |
|
|
|
CNS 12337
2017 Edition Pliers for radio ( replaced by CNS 1137 ) 扣環鉗 |
|
|
|
CNS 13143
2017 Edition Method of Test for Internal Bonding Strength Paperboard ( Using Z- direction Tensile / Compression Tester) 紙板內部結合強度試驗法（使用Ｚ–方向拉／壓式試驗機） |
Translated |
|
|
CNS 9366
2017 Edition Method of Test for Low Frequency(Below 3 MHz) Electrical Connectors (TP - 13 Mating and Unmating Forces) 頻率３ＭＨｚ以下電連接器檢驗法（配對及分離力量ＴＰ–１３） |
|
|
|
CNS 4998
2017 Edition Long Shank Machine Taps with Nominal Diameters from 3 to 24 mm 長柄機力螺絲攻（標稱直徑自３ｍｍ至２４ｍｍ） |
Translated |
|
|
CNS 2388
2017 Edition Method of Test for Combustion Rate of Cigarette Paper 捲菸紙燃燒率試驗法 |
Translated |
|
|
CNS 14492-3
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part3:Receivers for amplitude-modulated sound-broadcasting emissions 不同發射類別之無線電接收機的量測方法-第3部:調幅聲音廣播發射適用的接收機 |
|
|
|
CNS 4663
2017 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽（片封式，嵌於塑膠製品內） |
|
|
|
CNS 3445
2017 Edition Method of test for milk and milk products - Determination of lactose content 乳品檢驗法－乳糖之測定 |
|
| Find out:6360Items | To Page of: First -Previous-Next -Last | [142] [143] [144] [145] [146] [147] [148] |
