"IC " CNS Standards List| Graphical Symbols | Method Test | Methods Test | Determination asbestos | General Rules | Method test | Method test | Bushes Plain | |
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with SpherICall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 13991
2017 Edition Fixed resistor networks with individually measurable resistors for use in electronIC equipment 電子設備用可單獨量測個別電阻元件之固定網路電阻器 |
|
|
|
CNS 13999
2017 Edition General methods of measuring the performances of ultrasonIC pulse-echo diagnostic equipment 脈衝式反射法超音波診斷裝置檢驗法 |
|
|
|
CNS 14512
2017 Edition Corrosion tests in artifICial atmosphere-General requirements 人造大氣中腐蝕試驗法-一般要求事項 |
|
|
|
CNS 9101
2017 Edition GraphICal Symbols of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖符號總則 |
|
|
|
CNS 12880
2017 Edition Cement Sack Paper Laminated with PlastIC Woven Sheet 塑膠編織貼合水泥袋紙 |
Translated |
|
|
CNS 538
2017 Edition Inspection Plug Gauge for MetrIC Thread Ring Gauge (Go End Limit, Fine, Medium and Coarse Fits) 公制螺紋樣圈之量柱及磨損量柱（通過端，精配，中配及粗配） |
|
|
|
CNS 11942-9
2017 Edition Methods for determination of arsenIC in copper and copper alloys 銅及銅合金中砷定量法 |
|
|
|
CNS 15421
2017 Edition OffICe furniture - Chairs 辦公室用椅 |
|
|
|
CNS 4320
2017 Edition Hexagon Head Bolts, Finished and Semi-Finished, MetrIC Fine Thread 六角頭螺栓（精製及半精制，公制細螺紋） |
|
|
|
CNS 12807
2017 Edition Quality Requirement for MICrofilm of Documents and Drawings 微縮品製作–文件及圖面微縮軟片品質之要求 |
|
|
|
CNS 13651
2017 Edition Measuring Methods for Light Emitting Diode(for CommunICation) 通信用發光二極體量測法 |
|
|
|
CNS 11112
2017 Edition Methods of ChemICal Analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 9364
2017 Edition Method of Test for Low Frequency(Below 3 MHz) ElectrICal Connectors (TP - 5 Contact Insertion and Removal Forces) 頻率３ＭＨｚ以下電連接器檢驗法（接觸端子插入、鬆脫及拔出力量ＴＰ–５） |
|
|
|
CNS 4038
2017 Edition Parallel Bench VICes 鉗工虎鉗（圓膛定座式） |
Translated |
|
|
CNS 3873
2017 Edition Method of Test for the Rear Hubs of BICycles 自行車（腳踏車）後輪轂檢驗法 |
Translated |
|
|
CNS 5521
2017 Edition Polyester Film Lamination for ElectrICal Insulation 電器用聚酯膜 |
|
|
|
CNS 326
2017 Edition Wrench Lever with ElliptICal Handle 扳柄，桿端具橢圓形手把 |
|
|
|
CNS 9565
2017 Edition Test Code for Accuracy of Single Spindle AutomatIC Lathes (Sliding Type) 單軸自動車床（車頭移動型）精度檢驗標準 |
|
|
|
CNS 11151
2017 Edition Method of Test for Unit Weight, Yield, and Air Content (GravimetrIC) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 10230
2017 Edition Test Code for Accuracy of SlICers 單板平切機精度檢驗 |
|
|
|
CNS 4447
2017 Edition Method of Test for Resistance of PlastICs to Chemicals 塑膠耐化學藥品性檢驗法 |
|
|
|
CNS 2228-2
2017 Edition PlastICs − Poly (methyl methacrylate) sheets − Types, dimensions and characteristics − Part 1: Cast sheets 塑膠－聚甲基丙烯酸甲酯板－類型、尺寸及特性－第2部：押出板 |
|
|
|
CNS 6453
2017 Edition Oil of clove stems [Syzygium aromatICum (L.) Merr. et Perry, syn. Eugenia caryophyllus (Sprengel) Bullock et S. Harrison] 丁香莖油 |
|
|
|
CNS 9563
2017 Edition Test Code for Performance of Single Spindle AutomatIC Lathes(Fixed Headstock Type) 單軸自動車床（車頭固定型）動態檢驗法 |
|
|
|
CNS 13214
2017 Edition BasIC Environmental Testing Procedures Part 2: Tests – Test Ec: Drop and Topple, Primarily for Equipment - type Specimens 環境試驗法（電氣、電子）–面落下、角落下及翻倒（主要為設備）試驗法 |
|
|
|
CNS 3326
2017 Edition Safety Code of High Pressure for Freeging DevICes 冷凍設備高壓安全規章 |
|
|
|
CNS 7962
2017 Edition Test Code for Performance of NumerICally Controlled Table Type Horizontal Boring Machines 數值控制床台型臥式搪床動態檢驗法 |
|
|
|
CNS 13229
2017 Edition Slowly Descending DevICes 緩降機 |
Translated |
|
|
CNS 13539
2017 Edition Excess Flow Shut - off DevICes for Liquefied Petroleum Gas 液化石油氣超流遮斷裝置 |
Translated |
| Find out:6418Items | To Page of: First -Previous-Next -Last | [143] [144] [145] [146] [147] [148] [149] |
